RC-Monster Forums

Page 2 of 2

Show 40 post(s) from this thread on one page

RC-Monster Forums (https://www.rc-monster.com/forum/index.php)

- Castle Creations (https://www.rc-monster.com/forum/forumdisplay.php?f=34)

- - Shv 200 (https://www.rc-monster.com/forum/showthread.php?t=23273)

nl12	09.01.2009 09:24 AM

I need more power, or at least want it. I am planning on about 370 pound vehicle with rider onboard.

Unsullied_Spy

09.01.2009 09:30 AM

Quote:

Originally Posted by magman (Post 317478)

so if the one mentioned is capable of 8kw of power, how much is the one at the top of the page capable of?

If it can handle 90V @ 200A that's 18,000 watts. Put a fan on the ESC to help keep it cool and you'd better be holding on to something when you put the coals to it because that's 24 HP.

whitrzac

09.01.2009 02:46 PM

I want a VID NOW!!!!!!

preeez:angel:

billy gunn

09.01.2009 02:56 PM

Quote:

Originally Posted by Pdelcast (Post 317470)

The Phoenix ICE HV-160 is just about ready for release, and that should do just about anything small like the above picture... 50V, 160A maximum.

That's about 8kW of power -- over 10hp.

And it's a beast -- we ran one on the bench at 240A for two minutes before it went over-temp and shut down.

That looks like it might replace the Jeti SPIN200 on my Baja, is it going to have car programming?

NVM found the answer on the Hydra thread. Looks like you are going to release car software. ETA on car software?

nl12	09.01.2009 04:26 PM

Will the SHV 200 controllers be able to be daisy chained? If so what exactly will that enable?

Byte	09.01.2009 04:54 PM

It will cost 800 dollar or something like that... :surprised::surprised::surprised:

BrianG

09.01.2009 04:56 PM

Quote:

Originally Posted by nl12 (Post 317583)

Will the SHV 200 controllers be able to be daisy chained? If so what exactly will that enable?

I would guess to increase current output or to allow multiple motors to be driven from one throttle signal input while maintaining sync.

nl12	09.01.2009 05:01 PM

Quote:

Originally Posted by BrianG (Post 317595)

I would guess to increase current output or to allow multiple motors to be driven from one throttle signal input while maintaining sync.

I hope it will be able to do both of those things, would be useful features.

BrianG

09.01.2009 05:06 PM

I've been hoping for an ESC that could be daisychained to a "master" ESC for some time now. Would solve the whole dual BL motor syncing issue to keep them at the same speed despite slight differences in motor kv or whatever. Making a 4WD Slash would be a simple matter then. :smile:

shaunjohnson

09.01.2009 05:27 PM

one day i AM going to get a 1000A ESC from castle and make my nissan manette (vanette) electric!!
there is soo much space under the chassis once the fuel tank is gone for batteries:yipi:

nl12	08.05.2012 03:56 AM

Bump, I still want one, 300 amp version please.

Bondonutz

08.05.2012 01:09 PM

Wow, old thread with a very interesting topic ?

Semi Pro

08.05.2012 04:14 PM

me too , but i dont think castle will make them with how the ice 160 turned out

SV6000

08.18.2012 09:17 PM

I would love for castle to make a speed controller to compete with the large MGM 40063 or 25063, or the 40.330 from schulze. Yes the controllers would be physically bigger than what they are now but 400A constant at 63V and 500A burst

All times are GMT -4. The time now is 05:11 PM.

Page 2 of 2

Show 40 post(s) from this thread on one page