RC-Monster Forums - MM update is up!

Page 2 of 5

Last »

Show 40 post(s) from this thread on one page

RC-Monster Forums (https://www.rc-monster.com/forum/index.php)

- Castle Creations (https://www.rc-monster.com/forum/forumdisplay.php?f=34)

- - MM update is up! (https://www.rc-monster.com/forum/showthread.php?t=9698)

BrianG

01.22.2008 04:36 PM

Quote:

Originally Posted by Just go Play (Post 143091)

I just tried this with my FLM Emaxx and a novak 6.5 I had sitting around and cogging is reduced to where this is a usable combo now. Previously cogging was so severe that the MM would over heat very quickly and required pushing the truck to get it to move.

This looks like a decent upgrade that should allow running some previously unusable motors with the MM.

Makes sense since Novak uses slotted stators, just like Neu...

crazyjr

01.22.2008 04:43 PM

I have not tryed it on a 4 poler, but i updated all three of mine. They all seem to feel better and start slower than before the update. I expect that they shopuld run cooler due to better startup

MetalMan

01.22.2008 05:10 PM

One thing about my test video, that 4s pack was basically dead when I did the tests, so it's possible that skewed the "after" part.

Anybody else notice how the frequency during braking has also changed? Makes that Neu sound really weird!

lutach

01.22.2008 05:17 PM

All I can say it is working with a 6 pole Mega using 4S lipos and that is good. I did try to use 6S and that was a no go.

BrianG

01.22.2008 06:05 PM

lol, 6s? Did you really expect it to work at 6s? How about something a little more reasonable like 5s...

lutach

01.22.2008 06:18 PM

Quote:

Originally Posted by BrianG (Post 143149)

lol, 6s? Did you really expect it to work at 6s? How about something a little more reasonable like 5s...

http://www.megamotorusa.com/images/Video/XRAYCar8.wmv

VintageMA

01.22.2008 06:45 PM

Interesting - downloaded 3.03 just before leaving work. Got home and all of a sudden 3.04 was available. Wonder what changed?

lutach

01.22.2008 06:49 PM

Odd. I downloaded again.

lutach

01.22.2008 06:53 PM

New firmaware as well. 1.17

Arct1k

01.22.2008 06:55 PM

Bug fix - It has gone to final now

Force a full re-arm after manual programming
Minor bug: setting drag brake via stick programming showed a custom value of 1% below the desired value on Castle Link
Minor bug: Loading and saving programming information to a file did not properly update calibration data

lutach

01.22.2008 07:31 PM

I just fried my MM. This stinks. I downloaded the new firmware and I just tried it again in my TC3. Plugged the 2S lipos and as soon as I turned the MM on, a few sparks came out.

glassdoctor

01.22.2008 07:42 PM

Want to trade one of your HW speedos for one of my MM? :)

lutach

01.22.2008 07:48 PM

Quote:

Originally Posted by glassdoctor (Post 143198)

Want to trade one of your HW speedos for one of my MM? :)

:lol: My HW is kicking butt. Drove it today until it hit the cut off and got 25 minutes run time. I might have found the right gearing for my TC3 and HW/N80 combo.

entjoles

01.22.2008 07:49 PM

well i tried the update on a novak hv 4.5 motor in the xt8 and it was much better as well, still cogged, but gearing way down may make it drivable but the kv rating is to high, the calc. said it was like 72k rpms and 85 mph, so i wont be running this!!!!!

cant wait till more reply, i think a neu is my next step:yipi:, as long as it this fixes the cogging

VintageMA

01.22.2008 08:12 PM

I am used to deadband being expressed as a % of the throttle travel. There doesn't seemto be any documentation on how Castle is expressing it in milliseconds. Also the milliseconds ratings of the trasmitter calibration seem odd. Any thoughts?

All times are GMT -4. The time now is 11:21 AM.

Page 2 of 5

Last »

Show 40 post(s) from this thread on one page