|
160n/cm? i think there is a small error.. 16n/cm would be closer..
|
Quote:
|
Quote:
|
1600 nmm is same as a 160 ncm
|
ah yes, i made a mistake, sorry bout that.:035:
it is 160Nmm. :027: that seems alot more realistic. |
@boss and sylvester;
1600N/mm is 160N/cm.. Ten points go to Leroy.. |
Quote:
1 In = 0.0254 m Ex. 16 oz-in = 16*0.278*0.0254 = 0.113 Nm Artur |
.113nm = 113nmm =11.3ncm
|
okay.
i wanna try something. need imput.:032: clods use 2 540 brushed motors. would the twin force work with 2 540's? i dont want too much power so it wheelies and stuff like that. i like to keep the nose on the ground. would power them with 2s lipo. |
Just go Brushless you will be much happier if you get the right setup
|
cant play alot when the motors cost 300€.:002:
i mean expirement.(spelling:032: ) |
feiago 85 bucks but dont know how much that is in other money but here that is about the same price a touring car motor that is used in the championship races that pros use.
|
Quote:
pinolelst |
can get decent mod motors for 35€ aswell.
|
I've been paying $50-60 for handwound mods for like 20 years now... prices haven't changed since the 80's
There are some nice machined wounds for $30-40 too like jolly says. |
high-end handwounds go from 85€ to 110€ here.
i was wondering, will mamba handle 2 motors (brushed):032: |
As long as they don't go over the rated amps for it. You good. Depends on
how you wire to. Parrellal and seires has two different amp ratings for same motors. |
plettenberg HP 290/20
any one know this motor well?
http://www.plettenberg-motoren.com/U...0_20/motor.htm |
Quote:
You could probably run quite a few brushed motors off of the MM. :027: I use the Mamba Max in my clod crawler, running 2 55t lathe motors in parallel. It is great for that application due to the drag brakes. |
one would need a data logger to be sure.
so one can measure amp draw of the motors. but i'm sure mambamax' wouldnt handle alot more then 2 motors. |
Granted this is with 55turn motors, but this is a post from rccrawler:
http://www.rccrawler.com/forum/showp...1&postcount=49 Quote:
|
ha yes.
that interesting. but mod motors pull more then 20 amps. |
Quote:
It supposed to have pretty good amount of torque. Artur = Griffin |
lets wait for artur to come by then.
|
Well he comes and goes. You may want to pm him. It may be easiest.
|
well, i have time. hahaha:005:
|
I have 355. Very nice motor. What parameters you are loooking for?
Artur |
i'm more into 540 to 600 size motor's for my twin force.
doesnt have to be fast, stock speed is really enuff for me. i'm interested in motor's that could do center diff drive. gearing with diff in the center would be 15/1 or so. |
Quote:
As for 540-600 johnson-mabuchi type motors then 55-turn or sensored BL would be the right choice. Artur |
i know how big the 355 is, its not for me.
and its to slow aswell. i'm lookin for motors that do 25k rpm. on 2s lipo. any way, how much amps and volts is the MM bec? |
Quote:
8.4V - 5V = 3.4V 3.4V * 2A = 6.8W of heat dump from BEC alone (continious duty) Artur P.S. I am a little bit confused, you want crawler? Check at megamotors in brushed section. |
no not crawler.
want slow basher. 30/40 kmh dont break stuff like that. and may make really tight track someday. also want direct drive in the future. 43/10 diff and center diff 46t. with 13t pinion that would make 15.21/1. need motors that can handle that. thanks for your help. mike. |
I think I know what you mean jolly.
I have a samiliar idea myself. I haven't figure out exactly what I am going to run either. |
do you want it to be able to crawl?
i dont really. i'm kinda thinking rwd now. save some weight and more fun. if its not overpowered it might make nice controllable slides that way. |
i have tried to trial drive my truck, you wouldnt believe have much fun that is.
so i may go with something really slow and crawleble anyway. need spool's . better taller tires. dish wheels. and so on. i love it. |
What are you running jolly? I am going to go for something not really slow but run like 15 to 20 top speed. I have locked my diffs already. It has some big joes on it as well. Moved the suspension and shocks to have great travel. I haven't tried it yet. Maybe tomorrow.
|
all stock twin force. except for center uni's.
mamba max esc. stock motors. 2s orion lipo 3200mah. thats the most important. thing to come: hb pro diffs, 4.3/1. 17mm wheels and better tires. better motors or only one motor if he is powerfull enuff.:D some sweet wiring so i can run 2s2p. maybe a integy sbec 5 amp if its any good<= any input on this?:032: |
help!
i dont know what i should do. i like bashing alot. but also trial and stuff. want center diff for bashing. but then it couldnt trial any more. what to do:032: |
Build another truck. That is the easiest. It is real hard to have one truck to do all.
You build a truck for every thing you want to do and you have it covered. :) |
i'll bash with with this one, then see bout the rest.
|
| All times are GMT -4. The time now is 04:30 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.