:neutral::neutral: were???

traxxas makes both.

ohh, he ment CVs... when I get the $$

any idea on a good tire that will hook up on a dry, hardpacked, dusty track???

its got a coating of dust(sand) on the top, and underneath its rock hard...

CVDs will work but for the centers because of the limited travel I use dog bones. A very simple, tough and efficient way to transfer power. I got mine from Mike here in RC-monster. My old chassis but you get the idea:

http://pic20.picturetrail.com/VOL143.../269751926.jpg

1 raceday down well, at least I didn't finish dead last, I beat a 2wd truggy and a guy who blew a glow plug...:oops: this is in a truggy class

I had a new first though, I snaped a traxxas hingpin into 3 pices, I didn't know they were that hard, usualy they just bend into a prezzal shape:lol:

I also broke 2 lower A arms... within 5 min of runing

the eaten servo count is up to 4, now I run a ofna saver on the servo since the maxx one is a POS


I'll have more pics of my new low cog CF chasses:yipi: 1 question, how diffrent are the tranny mounting holes on a 3906 and the 3905??


a few new pics...

bow-tie, stock, muggy
http://i272.photobucket.com/albums/j...x/IMGP4864.jpg
wing mounted
had to cut the tailgate out...
http://i272.photobucket.com/albums/j...x/IMGP4861.jpg
muggy VS. bow-tie
http://i272.photobucket.com/albums/j...x/IMGP4865.jpg
RTR, ready to Rock!!

http://i272.photobucket.com/albums/j...x/IMGP4866.jpg
http://i272.photobucket.com/albums/j...x/IMGP4867.jpg

not soo much and the hubs are still 17mm:lol:

BTW, I'v got hot pink too
http://i272.photobucket.com/albums/j...x/IMGP4862.jpg

i would run the bow ties, less rotating mass. if your looking to get a better servo saver system,mod the stock one like i did.

what did you do??

after 2 racedays, my brand new set of center driveshafts are done...:whip:


whats the most afordable upgrade for the FRONT center shaft on the 16.8v e-maxx??:neutral:

the only upgraded center shafts I can find are the TRX ones...


pics from practice day, race day it rained all day< it kept the track nice and tacky, but he didn't want to get his camara wet...


http://i272.photobucket.com/albums/j...maxx/maxx4.jpg
http://i272.photobucket.com/albums/j...xx/maxx2-1.jpg
http://i272.photobucket.com/albums/j...-maxx/maxx.jpg
http://i272.photobucket.com/albums/j...maxx/maxx3.jpg

no, the camara was not upsidedown:whistle:
http://i272.photobucket.com/albums/j...maxx/maxx2.jpg
http://i272.photobucket.com/albums/j...maxx/maxx1.jpg

the day after, BTW this is after only 7min of the 15min main...

lower A arm

http://i272.photobucket.com/albums/j...x/IMGP4953.jpg
http://i272.photobucket.com/albums/j...x/IMGP4954.jpg
http://i272.photobucket.com/albums/j...x/IMGP4958.jpg
http://i272.photobucket.com/albums/j...x/IMGP4956.jpg


:grrrrrr::grrrrrr:
http://i272.photobucket.com/albums/j...x/IMGP4957.jpg

yup ive broken that same part the same way

are these any good???

http://cgi.ebay.com/Traxxas-New-E-Ma...3%3A1|294%3A50

Yup, I heard those'll work fine.

I'v seen arms, towers, etc made by proline, are they any better, or what do they do???

better then ? get rpm and dont look back.