RC-Monster Forums
Page 3 of 3 12 3
Show 40 post(s) from this thread on one page

RC-Monster Forums (https://www.rc-monster.com/forum/index.php)
-   Brushless (https://www.rc-monster.com/forum/forumdisplay.php?f=12)
-   -   80b shutting down ? (https://www.rc-monster.com/forum/showthread.php?t=3736)

BrianG 08.08.2006 11:26 AM
Um, that motor doesn't look too healthy to me...

jhautz 08.08.2006 12:12 PM
Quote:
Originally Posted by stampy
i think your right they are 4mm lame:002: what about a lenher xl 3600 would one work in a rusty? a new motor is a must now! :035: dont know what happend but i know its bad
The XL3100 would be great in a rusty. I ran a XL4200 for a while and it was really good. But I went to 3s Lipo and needed to get a lower KV motor.

You could even just run the Basic 3100 (not XL) and it would be really good.

stampy 08.08.2006 12:20 PM
would a xl3600 on 3s work well with my quark 80b?

stampy 08.08.2006 12:39 PM
nvm its 97 amps:031: any body know how powerfull a Kontronik Twist 42 is? jamie from starluck said he would sell me one for like 140 should i do it:002:

jhautz 08.08.2006 01:16 PM
4200kv seems like it would be too much for 11.1. You will be reving it really high and it will probbly run hot. I got rid of my XL4200 cuz it ran to hot on 3s. I would recomend going for something more in the 3000-3500kv range. You can gear ir up and get just as much speed, it just runss cooler. Especially if you go w/ the basic XL. It will have plenty of torque to gear it up.

I really think the Basic 3100 would be ideal for a rusty on 3s.

squeeforever 08.08.2006 01:16 PM
The XL3600 should work well I would think. Somebody correct me if I'm wrong though.

stampy 08.08.2006 01:21 PM
97 amps is to much for the 80b though :(

squeeforever 08.08.2006 01:24 PM
You can't go by that rating...The XL3600 in a ST on 3S shouldn't pull that many amps.

jhautz 08.08.2006 01:27 PM
Quote:
Originally Posted by squeeforever
The XL3600 should work well I would think. Somebody correct me if I'm wrong though.
I think the XL3600 would be fine as well. I wouldn't go any higher kv than that though or it will run to hot. As far as the 97 amp rating. You won't draw anywhere near that on 3s with a light rusty. If you had it geared up on 4s in an emaxx or something then you might.

When I had my XL 4200 in my (relatively heavy) all aluminum rusty, it would peak at 68-70 amps on 3s and that is a more power hungry motor than the xl3600. Your quark is an 80A constant rating. I ran my XL4200 on a Warrior 7020 (70 amp rating) w/ no issues. You will be fine.

stampy 08.09.2006 10:16 AM
cool sweet guees ill order it up today :018:


All times are GMT -4. The time now is 06:27 AM.
Page 3 of 3 12 3
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.