RC-Monster Forums - Hippie's GTP Project

Page 4 of 9

« First

Last »

Show 40 post(s) from this thread on one page

RC-Monster Forums (https://www.rc-monster.com/forum/index.php)

- General Discussion (https://www.rc-monster.com/forum/forumdisplay.php?f=20)

- - Hippie's GTP Project (https://www.rc-monster.com/forum/showthread.php?t=15848)

What's_nitro?

10.19.2008 07:53 PM

Lookin' good!

rchippie

10.19.2008 07:57 PM

Thank you :smile:

Does anyone know if they make a plastic spur to replace the steel one on GTP ?.

lincpimp

10.19.2008 08:31 PM

Quote:

Originally Posted by rchippie (Post 224118)

Thank you :smile:

Does anyone know if they make a plastic spur to replace the steel one on GTP ?.

If it is the single speed, the ofna 51t plastic spur bolts right on.

rchippie

10.19.2008 08:54 PM

Quote:

Originally Posted by lincpimp (Post 224123)

If it is the single speed, the ofna 51t plastic spur bolts right on.

Yes it is a single speed james . Thats great news . I was going to ask if this could be moddedd to fit ? .

http://www3.towerhobbies.com/cgi-bin...?&I=LXHSY8&P=7

Arct1k

10.19.2008 09:23 PM

ofna do one to I think it is for the pirate - I can check when I get back on ties

What's_nitro?

10.20.2008 03:16 AM

Quote:

Originally Posted by rchippie (Post 224129)

I was going to ask if this could be moddedd to fit ? .

http://www3.towerhobbies.com/cgi-bin...?&I=LXHSY8&P=7

Probably. You could use the steel spur as a template for the four holes.

BL_RV0

10.20.2008 09:06 AM

Do they make a plastic spur for the hyper ST centre differential?

lincpimp

10.20.2008 09:27 AM

Quote:

Originally Posted by BL_RV0 (Post 224225)

Do they make a plastic spur for the hyper ST centre differential?

If it is the std plastic case non-spider design, a kyosho plastic spur will work. They only come in 44 and 46t though, but should work since the st has 11/43 diff ratio.

lincpimp

10.20.2008 09:29 AM

Here is a link to the gear that will fit the gtp: http://www3.towerhobbies.com/cgi-bin...?&I=LXBM16&P=7

rchippie

10.20.2008 10:51 AM

Quote:

Originally Posted by lincpimp (Post 224231)

Here is a link to the gear that will fit the gtp: http://www3.towerhobbies.com/cgi-bin...?&I=LXBM16&P=7

James that gear would be the easyest to use since there would be no modding needed . I was just trying to use the stock ratio if possible .

lincpimp

10.20.2008 10:54 AM

Quote:

Originally Posted by rchippie (Post 224245)

James that gear would be the easyest to use since there would be no modding needed . I was just trying to use the stock ratio if possible .

That is the gear I use on my gtp with the kb45 motor. I have not had any issues with it so far. I do not like steel spurs due to the noise, and the only 6mm bore pinions I found were not hardened, so I had to use a plastic spur.

rchippie

10.20.2008 10:58 AM

Quote:

Originally Posted by lincpimp (Post 224248)

Thats the reason i want to use the plastic spur because of the noise .

lincpimp

10.20.2008 11:08 AM

Quote:

Originally Posted by rchippie (Post 224249)

Thats the reason i want to use the plastic spur because of the noise .

That is the main reason I use them. And hopefully it is slightly weaker than the glue used to hold the magnet on the motor shaft. I would rather replace the spur than the motor.

BrianG

10.20.2008 12:41 PM

Quote:

Originally Posted by rchippie (Post 224249)

Thats the reason i want to use the plastic spur because of the noise .

Just put a stereo on your vehicle. And yes, it's possible (I've done it).

lincpimp

10.20.2008 01:01 PM

Quote:

Originally Posted by BrianG (Post 224273)

Just put a stereo on your vehicle. And yes, it's possible (I've done it).

I had not seen that before, thanks for the laugh!