Speed Pede Project...
 

Well my pede hasn't had much attention lately so I gave it a bit of a make over...

I think the motor (CC 1515 1Y 2200) is overkill but needed to run it in something - I can't get a MMM in there though as the motor wires aren't long enough so opted for a trusty MM.

I inverted the RPM bumper and added some lead to help keep the front end down. I think I may have to lose the wing but will see what happens... I checked and it looks like a revo 2.5 body that I have will fit pretty well if I lose the wing...

Any other suggestions?

Differential Ratio: 1
Transmission Ratio: 2.727272727272727
Other Ratio: 1
Spur Tooth Count: 40
Pinion Tooth Count: 20
Total Voltage: 18.5
Motor KV: 2200
Tire Diameter (inches): 4.1
Tire Ballooning (inches): 0
Motor Current Draw: 0
Motor coil Ω: 0
Spur/Pinion Ratio: 2 : 1
Total Ratio: 5.45455 : 1
Tire Circumference (inches): 12.88 inches (327.17 mm)
Total Motor Speed: 40700 RPM
Vehicle Speed: 91.01 mph (146.2 km/h)
Estimated Adjusted Speed: 79 mph (127 km/h) - 13% loss
Effective KV Value: 2200

http://i168.photobucket.com/albums/u...k/Pede/034.jpg
http://i168.photobucket.com/albums/u...k/Pede/035.jpg
http://i168.photobucket.com/albums/u...k/Pede/036.jpg

That has got to be the coolest pede I've ever seen. :yes:

You should opt for a rustler chassis in favour of the pede one.

Have plenty of spare parts on hand! :lol: 80 MPH crashes are not pretty!

Sweet Pede, what motor mount is that?

That's the FLM tranny case.

Looks great! I like the wing on there.

Does it work with a Bandit to?

I can't see why it wouldn't work with the bandit. If the rear end of it is the same as a rustler and Stampede, it will work just fine. :wink:

The wing in from an OFNA LX - just shorten the centre posts a little.

The motor is a Castle Creations 1515 1Y

That makes me almost wish I hadn't gotten rid of my Pede a few months ago...

Nice PEDE :mdr:

Chassis looks interesting, is it the thunder tech chassis? I have a g10 chassis that looks alot like it, with the bell crank steering, from thunder tech.

I think it is an Xtreme Racing chassis... I ran on 4S and clocked an easy 55... However I broke the diff internals so need to order some more... :(

I really need to find somewhere flat and a radar gun - The GPS really needs a lot of space to get an accurate reading...

PS the shock setup is sweet though...

Nice pede. Now that you posted a pic of your CC 1515, Ben can aswell...

I thought he had already which is why I posted mine...

Little bit late there ryan?

My Motor thread- started October 16th.

Ryan has been offline for quite some time. *Cough* not sure why.

Dang! Someone beat me to it! lol A wile ago i tried to get my 9xl to fit into my rustler but my swamibar was in the way and the 9xl wouldn't fit. lol

Nice PEDE tho!!! I'd really love to see a video of that thing run!!!!

Lutach we need to meet up :)

http://i140.photobucket.com/albums/r...y/DSCN1511.jpg
I've already done this...insane power for the platform.

http://i140.photobucket.com/albums/r...y/DSCN1515.jpg
24/38 fit just fine and it had more than enough power, I could go to a 34T spur and whatever the biggest pinion is and still have power left. I wasn't able to get my Rustler completely set up for speed before this thing stripped a stub axle (twisted the U-joint right off). It's very heavy, but it goes like stink!

Whoa.

JEEZ!!! That'll deff fly now

Done this , been here :) only I was running a Novak 4.5. I only managed right over 70,then it was just to uncontrollable on foams.It would start drifting and correcting would make it go haywire. I did not run lead up front,I added a little wing to the bumper.It had no trouble keeping the front down.But it was very unstable. Good luck with this,I always thought it had 80 in it.For the diff you could try this http://cgi.ebay.com/ws/eBayISAPI.dll...%3D4%26ps%3D42 then use Jato shafts and your about as strong as it gets.

Overpowered 2wd trucks are great.

Fixed that for ya! :lol:

I like it better this way... :yipi:

Snell, your the king of overpowered 2wd trucks...

:lol::party:


The scary thing is that I can add 2 more A123 cells in the Rustler:diablo:.

SHEW!! DANG!! I just thought about it and what if you took the tranny out and hooked an outrunner motor up directly to some really strong driveshafts and fitted bigger, more stable tires on it.

Uhh, are you an R/C terrorist?? Why are you telling people how to build bombs!!! :lol:

all a rocket is is a controlled explosion:wink:

But an out of control rocket can explode. :rules:

That's been next on my project list for some time now.

so :P:yes:

'sposions are fun:yes:

Arkt1c, you better get some video of that thing in action! nice build. as bad as pede's are with wheelies have you considered a straighter wheelie bar?

And that's what the e-maxx driveshafts, custom limo chassie and body, lead weight, and tires from the future are for! to help controle the explosion lol

Oh and would this help any?

http://i36.tinypic.com/sw4ldc.jpg
http://i38.tinypic.com/53tndi.jpg

it's a 1/5 scale F1 car front wing

dunno if it'll help, but it'll sure look goofy as hell!

That thing is huge. How are you gonna mount it?

Does your truck run on AA batteries?

Those are fightin' words round' here!:diablo::bad:







:lol:

:mdr:

humm.......duck tape it to the body lol and AA betteries???? humm....yes! lol i've got a 2s lipo, MM, and 4 AA batts in it lol so it partually runs off of AA's