I Think I Broke My System!!!
 

i did a backflip and had a bad landing. Than it stopped, i took ti home and lifted it up. when i pull on thorttle, it coggs ALOT. Im on 1/3rd full throttle and it still coggs... I tempted the motor at 180... It was only 16 cells. I was tempted.... Plz tell my my ewsc is fine, and that its just hte motor!

You may have messed up the esc. Did it land on the esc or just jar it real hard? Make sure all your connections are still tight.

Nbcazn. Did you try the flip without the body

You might of bent a CVD or something, or broke a tooth on spur? Can relate to a "cogging" effect.

check your batteries. might have a loose battery bar or you might have knocked something loose in the esc like a cap or resistor or something.

I tookt he motor out, and it COGGS like crayz. Its not in the revo or anythign either...

did you check the batteries?

did you check your wires. batteries. and stuff

You probably wont find anyone to trade with you this time, buddy. Though I'm not sure.

batts are fine, so are wires. OH shoot...i smell something on the esc. It smells liek my 959 when im charging batts. DONT TELL ME IT FRIED? its temp was only 130!!!

temps not everything. you could have had something shooken loose or something.

inside the esc?

It doesn't sound too good..
phil

yes, inside the esc. i know that metalman has had a similar problem i think. he opened it up and had a missing resistor and a broken chip fet i think.

lol, how much woudl ti cost to send it to BK and have them fix it? I dont wanna messs with this stuff

email mike. he might be able to fix it. if you feel comfortable taking the shrink off i certainly would to see is there is anything wrong.

p.s.-did you see if the jumpers were on? red AND black? the black being missing might cause this.

I damaged a Warrior 9918 after a bad landing from a jump. Opened up the shrink wrap, to find that one of the parts on the bottom was chipped pretty badly. Mike sent me a part to try, but it still didn't work. So then I sent the controller to Mike, and he was unable to fix it, so he sent it to BK.

P.S. Mike, any info. about the controller?

how long ago did you damage the 9918?

It was originally damaged around the middle of August, and I think Mike sent it to BK around the end of October.

How do you mount the controller to the truck so that it wont get damaged? you cant exactly wrap it in bubble wrap cause of the heat, so what can you do?

Just make sure that the controller is not able to directly hit the ground. and pad it with some foam. the bottom of the pcb is rather fragile. i still don't understand why they don't make a standard esc holder. it would add some weight, but the safety might be needed in some cases.

I used two aluminium U-profiles to mount a controller.

i did dafni style mounts. so it should be fine, had body on and eveyerthing. WHeres teh black jumpoer located? I tried to find ti before but never could.

about 3/16 of a inch back from the red.

SHOOT
black is msisign, but i thought u needed to remove this in order for u to use a rx pack

yes. try it with a rec. pack. that might fix the problem.

ive always been usign a rx pack

your screwed lol. did you pull the shrink off and look at it? email or pm mike and see what he says.

oh god.,...OH GOD! NOOOOOOOOOOOOOOOOOOOO :(

Welcome to the excitement of burned out BL controllers. I've burned out 2 Warrior 9918s, and one MGM 12012. You don't know frustration yet ;).

well it dint smoke. And it still runs. So i dont think its burnt. Though there is a smell to it now.... Maybe its cuz it got hotter than usuall. Before, i the temps never went past 80. Thats cuz it was usualy 30 degrees outside

I should see your controller anytime, Travis. Nbcz...my money says you knocked something loose.

Really?!? I wasn't even expecting it very soon. Any idea on repair costs?

when stuff is knocked loose, is it ez to fix?

Sometimes. In my case, a chip was partially damaged, but replacing it didn't seem to fix the problem. That's why Mike sent it in to BK.

opened up the esc, nothign is loose. Looks perfect. Most likely is interneal. So im screwed. Any1 wanan buy a damaged esc?

Send it to Mike to get it fixed! Or, just have Mike take a look at it.

yeah, don't loose faith too quick Nbacz!

ima send out to mike this friday or sat.

Hey mike! if u see this, i sent out esc monday! hsould be there wed or thursday!

Mike says the esc is perfectly fine.... lol, theres a waste of time. I asked mike if he could put it on a car and test it out ot be 100% sure.