Lightning Pro-R its finish!!!
 

Hallo boys this is my new lightning, with Lehner 1930/8 Quantum-pro 80, and 4S flightpower lipo.
:004:

Cool!! is that a 1/10th body?

Wheels look sexy on her..

Sweet looking truck! Whats it look like under the lid??? I'm always interested to see how people executed their conversion.

Like this;

http://www.rc-monster.com/forum/showthread.php?t=4227

Yes Rene is a proline maxx body (for T/Emaxx) :)

Niiice truck. Planning any Vids?

Yes the vids will come tomorrow...

Cool will be looking

Nice looking truck! Always liked those sun wheels.


Thank you,
Promod

I know he also has got some cool looking slot 8's as well..

AAAAAAARRRRGH!!!!!
My friends i have a big big problem, Today I have tried the truck, went very well, but during the test to a sure point the motor did not work, the steering yes, in the video looks at that to the firm end… Creed that the esc has problems, does not feel no sound from the motor when I program it,the light on the esc is ok, but the motor don't spin, and the sound when i program it, it is not listened to!!!

this is the vid :(
http://www.brushless-italia.it/lightning.rar

Did you tried your eagletree to see how many current it takes?

And was the motor hot when it happened?

Yes Rene this is the amp draw graph...
Seems ok

Was the motor hot?

The temperature of the motor is 68 c°
The esc 55C°

That't not too hot.

This is odd..


I am downloading the movie to check it out.

Hang on..

Try another channel on your receiver. Might be dead.. Happened to me too..

The receiver is ok , itry the receiver with onother esc and works ok...

Did you used an UBEC with the speedcontroller?

Just saw the movie.

no i use internal bec

I would personally use a seperate UBEC with it. have you got one you can test it with? the only option i can think of at this moment is that the BEC is dead.

But the servo steering works ok...
Rene' look the lipo volts...too low for me

NOt good!!!!

In effect the pack it seems swollen...

Thats very bad, i would contact flightpower, sounds like a bad cell to me.

nevertheless I had set up the cut-ff of the quark to 3.0 volts

???

how come it didn't cut off?

Are you sure you had it set to the correct battery type? If you have it set to NiMH the Quark still lets you set a lipo cut off voltage and you might think you have it set to Lipo.

I dont know, but controller broke+battery failure....
AAAAAARRRRRGHHHHH!!!!!!

I set cut-off 3 volts per cells...

Crap.. Something went very bad on this..

:035: :035: :035: :035: :035: :035: :035: :035: :035:

I'm really sorry to hear this, man!
Dont you have another lipo pack to use with another controller?

Those lipo's didn't do what they should do in the first place. They should never drop that far in voltage on a 120A peak load. and the controller should have used it's cut-off on 12V.. I really don't get this..

is the entire pack swollen or is it 1 cell?

The pack at full charge is 16 volts, and very little swollen creed is not damaged seriously

Though it should NEVER drop that far.. those cells are not good. I would contact flightpower about it. They should stay above 3V per cell on a 50C load..

Yes rigt

For the quark Rene, What tasks that it has succeeded??

The quark failed with the cut-off?

The quark not work...
Not sound for motor, motor not spin, the led is ok, and the steering servo with internal bec is ok