Schulze did something AMAZING...
 

Oh my GOD!! All the oceans must've turned into blood or something.... Shulze really surprise me with this one... I sent in my 18.129, and they're replacing it for FREE!.. I'm still shocked as of right now... they're even paying for the shipping cost... Unbelievable... I must've did something good to deserve this ;)

Nah, you just didn't do anything bad... ;)

It's nice to have things work out to your advantage once in a while huh?!

Yeah... for sure man..... Got my GST 7.7 This week and this good news from schulze (the only good news)..
BrianG... yeah, you're right!!

LOL!

Schulze showed themself from their best side to me.. My schulze receiver died.. They charged me 15 dolllars for repair.. Not too bad, but i would say that it was still in warrantee, only being a month or 7 old..

What do people think about BK returns/rapair policy? I have an old 9920 which is broken, no wires or insulating, just the circuit boards basicly - do you think BK would replace it?

hi there!

was it still in warranty?

i am still looking for a motor for my savage, a maxximum pletti is still sitting on my shelf.

should i try to send in my destroyed and "reglued" 18.97 and order a 32.170 at the same time? hoping to get a good discount for the 32.170 ? :005:

should be worth a try...

on the weekend i f*cked up a hacker master comp opto with a c40l 10turns in my madforce. the 10cm high grass simply was too much.

i installed a 6.5hv novak with a 12t pinion after that and the grass was no more problem!

the madforce is not fast but it´s fun to drive.

what do you guys think about dual brushless setups?

i once had dual c50s in my maxx and fright both hacker master optos after that i removed the dual setup and replaced it with a lehner 1940 which is still in use.

BTW - the madforce is a nice car. but i think the diffs will die very soon. i give them 4-5 runs...

Marc.

P.S.: i just looked at the price of a 40.160. yeah it is at over 600euros! no way... i will sell the maxximum on ebay. i have one 32.170 that is enought. i think it´s better to invest money in the stock market than in schulze controllers...

I think they might replace it, but it will cost you something i'm sure of it......wouldn't hurt to ask....you never know how much the repair might be.......

Maybe less people buying them so they figure they change up some.

valid point chc.....but it was a smart move by schultz

In regards to the 9920, all you can do is ask. I can't say that they are the best in communication though. I had Mike send my 12020 back and it took months (which Mike has still not rec'd back yet). It's not Mike's fault by any means, but you'd think a good customer as he is, they would do more for the guy!!!!!!!!!!

It cost me $75 USD one time and $85 the other. The first time, it took 4 months, the second time 6 months. Most likely they won't replace it for free.

I have had some luck communicationg with BK...but sometimes you don't have such good luck...I agree...with the amount of their stuff mike sells...you think they would treat him better

I actually fried my 9920 and they replaced it for free...I think it got a little wet from a little puddle, but still don't know to this day...And it only took about a month for them to replace it....

I'll probably try fixing my 9920 myself. I don't need it, have another, so I might as well give it a go, not losing anything, lol.

IMO, you are lucky! The last 9920 that came back I sold quickly after getting it. There are better companies out there than BK... (CC)

Yah know, I haven't had any problems with my BK 9920... But never had any luck with the schulze controllers except the 40.160..... that thing NEVER got warm.... But I still wouldn't buy from schulze... it's so hard gettin' warranty from overseas... in just a pain in the *ss..... hey, if you don't want the broken ESC, I'll take it and send it... ;) j/k, but seriously... :)

I sent three esc off and haven't seen them in like 6 months. What service that have. I not worried about getting them soon but would like to atleast know i am getting them back. I never had a problem with the schulze i have. I have been beating on it for well over a year now.

That sounds a bit of a relief, Leroy.

I hope I wont see the day when my 149.18 get grilled in smokes.....:(

Hey, I take my words back... Shulze did do something amazing.... amazingly stoopid.... after about 1 minute of running the schulze in my 2nd LST with a 18.129 and 7XL.... I can't even remember how many times this thing went in for repair... less than one minute and the M/T was cogging stupidly.... so I thought it might be the batteries... but looked at the schulze.. a few of the fets where somewhat burnt... I really don't like schulze esc.... it's not that badly burnt.. but I can take a pic and send it to you serum, if you'd like... F*cking schulze.... I only tested it with 3 Cells also.. and it's not even over geared... less than one friggin' minute... and dead...

Yeah, get me the picture please....

I guess you had a loose contact Aqwut..

Too bad this happened to you.. I am curious what they say about it..

UhOh! I see bad wind in the horizon.

No way !

the schulze dies with fire if there´s contact problem...

It was definetly .... Yeah ....

THE WIRES ARE TOO LONG !

Shame on you.

Marc.

What is the deal with schulze?
If they fix it for free it would be nice.
If they say loose contact or wire to long. They suck. It is nice when they work
right.

they just fixed that Sh*t for free.. .. it was fixed untill I used it... I wonder what kind of excuse they're gonna use this time.... I used 5.5mm connectors for everything.. motor end and wire end... I wonder if ICARE would let me trade for a different ESC and MGM or something.. before I was paying too much for repair.. now I'm paying too much and too frequently for shipping.... Schulze is gonna burn in H*ll.... If I lived close to them, I'd definately pay them a visit.. maybe egg the company with some chinese salted rotten eggs..... hhaahaaahaha