RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 10 of 10
Search took 0.02 seconds. Search: Posts Made By: Steeni
Forum: Slipperential discussion 10.13.2009, 12:59 PM
Replies: 146
Views: 131,815
Posted By Steeni
Np, as I said it's working now. But I would...

Np, as I said it's working now.
But I would say that the scuffing of the pressureplate on the slipperside is a must, the slipperential did overheat badly after roughly 3 minutes on the track before...
Forum: Brushless 10.12.2009, 04:00 AM
Replies: 1
Views: 2,621
Posted By Steeni
PWM timing for Castle/Neu 2200 kv

Fried my MMM again and now I'm fed up with this thing.:diablo: I'm using my MGM Z3 again.

Only have 1 question regarding PWM setting for the MGM, can't find the information anywhere on the net,...
Forum: Slipperential discussion 10.12.2009, 03:48 AM
Replies: 146
Views: 131,815
Posted By Steeni
Ok, installed it in my Losi 8eight-T and it's...

Ok, installed it in my Losi 8eight-T and it's almost a drop in.
Only thing that has to be taken care of, at least if you're using Mike's motormount is the fact that the spurgear will be touching the...
Forum: HPI Savage 09.06.2009, 01:53 AM
Replies: 19
Views: 14,123
Posted By Steeni
Voltage measurement in such devices typically has...

Voltage measurement in such devices typically has a precision of +/- 5 %.
For 4.2 V that means +/- 0.21 V. So seeing 4.4 V on a cell is perfectly possible.

If you read the instructions on some of...
Forum: HPI Savage 09.05.2009, 03:32 PM
Replies: 19
Views: 14,123
Posted By Steeni
Well, you're right if you're assuming that only...

Well, you're right if you're assuming that only the overall voltage counts as cutoff, means 8.4 V for a 2s Lipo pack. Your problem is the fact that on your "bad" pack a cell seemed to have drifted a...
Forum: Truggy 04.07.2009, 12:15 PM
Replies: 17
Views: 6,481
Posted By Steeni
Ordered today, will post some more pictures after...

Ordered today, will post some more pictures after I have it mounted and going :yipi:

IŽll go for a higher grade oil all around now, I have tweaked my suspension further now and can instantly turn...
Forum: Truggy 02.23.2009, 01:06 PM
Replies: 17
Views: 6,481
Posted By Steeni
Yes, ofc, and to be honest, never doubted it. I'm...

Yes, ofc, and to be honest, never doubted it. I'm using Mamba controllers since they appeared on the market and must say that I yet have to see one going down. I ran both 1/18 and 1/10 versions and...
Forum: Truggy 02.22.2009, 12:16 PM
Replies: 17
Views: 6,481
Posted By Steeni
Hey and thanks for all the feedback... Well...

Hey and thanks for all the feedback...

Well the MGM controller seems to do fine now and had my first full run. Reading the blackbox data and "feeling" the thing move gave me some directions, that...
Forum: Truggy 02.12.2009, 03:29 PM
Replies: 17
Views: 6,481
Posted By Steeni
Hmm....seems you're running an even higher gear...

Hmm....seems you're running an even higher gear ratio then me...with 6s!

What motor do you use in that setup, All I can see it's no Castle/Neu and it seems smaller then mine?

And yes, I did try...
Forum: Truggy 02.11.2009, 07:11 PM
Replies: 17
Views: 6,481
Posted By Steeni
My first 1/8 BL conversion

Well hello :yipi: to all and since I'm new to this forum, I'll start with my newest project, a Losi 8ight T. Used a Race Roller chassis I got from a german teamdriver and started out with a MMM &...
Showing results 1 to 10 of 10

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top