RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 17 of 17
Search took 0.00 seconds. Search: Posts Made By: zviper
Forum: Brushless 12.05.2009, 09:04 PM
Replies: 17
Views: 11,263
Posted By zviper
that esc combo is alot cheaper then that 300 odd...

that esc combo is alot cheaper then that 300 odd $$ esc you want to get. plus you get a motor to sell or keep as a spare. or buy a MM
Forum: Buggy 11.16.2009, 12:05 PM
Replies: 8
Views: 3,120
Posted By zviper
ok thanks for clearing that up, i got my 8b 2.0...

ok thanks for clearing that up, i got my 8b 2.0 second hand. it didnt even have any grease in the bulkhead
Forum: Buggy 11.11.2009, 12:08 AM
Replies: 8
Views: 3,120
Posted By zviper
im talking about the gears inside the diff.

im talking about the gears inside the diff.
Forum: Buggy 11.10.2009, 05:56 PM
Replies: 8
Views: 3,120
Posted By zviper
these...

these http://www.greathobbies.com/productinfo/?prod_id=TMLA3501 ? if so i have four in there, one on either end of each of those nothched pins.
Forum: Buggy 11.10.2009, 05:48 PM
Replies: 8
Views: 3,120
Posted By zviper
im still unshure what shimming is.

im still unshure what shimming is.
Forum: Buggy 11.10.2009, 05:36 PM
Replies: 8
Views: 3,120
Posted By zviper
Losi 8b diff gears

well i have 2 blown out drive bearings and the gears on the inside are rounded pretty bad. i have some spare hellfire diff gears they fit but i just want to know if is compatible. or is it just too...
Forum: Castle Creations 11.03.2009, 12:15 PM
Replies: 174
Views: 44,289
Posted By zviper
ok so its a little more complicated then i...

ok so its a little more complicated then i thought. i guess when i get new batts ill pickup a new charger. thanks patrick, awesome product btw
Forum: Castle Creations 11.03.2009, 12:11 PM
Replies: 174
Views: 44,289
Posted By zviper
bernie i dont have a charger that reads internal...

bernie i dont have a charger that reads internal resistance. can i use a volt meter to get the internal resistance ?
Forum: Brushless 10.29.2009, 06:44 PM
Replies: 13
Views: 5,720
Posted By zviper
i used adhesive shrink tube if that helps

i used adhesive shrink tube if that helps
Forum: Brushless 10.29.2009, 05:31 PM
Replies: 13
Views: 5,720
Posted By zviper
close enough lol

close enough lol
Forum: Brushless 10.29.2009, 05:15 PM
Replies: 13
Views: 5,720
Posted By zviper
ok so i went ahead and just bent then and tinned...

ok so i went ahead and just bent then and tinned them worked wonders. i dont see the problem with using shrink tube on a 90. thanks for the help guys
Forum: Brushless 10.29.2009, 03:05 PM
Replies: 13
Views: 5,720
Posted By zviper
so instead of making it 90. just grind out the...

so instead of making it 90. just grind out the bullet so i can angle it around 45?
and what about cutting my cc2200kv motor wires do they all have to be the same length?
Forum: Brushless 10.29.2009, 02:45 PM
Replies: 13
Views: 5,720
Posted By zviper
90 degree bullet connector?

can i drill out the side of a 6.5mm bullet connector will that work or would it be a waste?
when i shorten my motor wires on the cc 2200kv do the wires have to be the same length?
Forum: Brushless 10.23.2009, 09:49 AM
Replies: 5
Views: 2,999
Posted By zviper
can some one post some insight, im going to my...

can some one post some insight, im going to my lhs today its a fair drive, so if i need something to make it work i can get it. if not im screwed for a month or 2 please help
Forum: Brushless 10.22.2009, 10:42 PM
Replies: 5
Views: 2,999
Posted By zviper
brushless rpm sensor promplems

i just picked up a eagle tree 150A with a few temp sensors and the brushless rpm sensor everything reads fine except the rpm its show 5750rpm when not moving. i set the brushless rpm setting on the...
Forum: Brushless 09.23.2009, 09:51 AM
Replies: 5
Views: 2,917
Posted By zviper
thanks simplechamp for the info i'm assuming my...

thanks simplechamp for the info i'm assuming my esc doesn't have that. do i need a data logger, are there any other brands?
yeah i have OVER 9000!! on the nitro killers forum lol
Forum: Brushless 09.22.2009, 07:39 PM
Replies: 5
Views: 2,917
Posted By zviper
new to brushless

i just recently got a mamba monster 2200kv combo. with a losi 8e and i installed the castle link software and i noticed theres a second program. caslte link graph viewer. how do i use that i cant...
Showing results 1 to 17 of 17

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top