RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 13 of 13
Search took 0.00 seconds. Search: Posts Made By: t-mange
Forum: Brushless 10.05.2009, 09:37 AM
Replies: 4
Views: 5,509
Posted By t-mange
In my 36-70-1600 I had 5x13x4 bearings last time...

In my 36-70-1600 I had 5x13x4 bearings last time I changed.
Forum: Brushless 06.03.2009, 04:54 PM
Replies: 10
Views: 3,112
Posted By t-mange
I think I'm pretty good with smooth throttle, I'm...

I think I'm pretty good with smooth throttle, I'm not the guy who uses the hammergrip to get out of bends. Just smooooooth on the throttle:yes:.

Where do you guys have your temp limit, I stop...
Forum: Brushless 06.03.2009, 04:36 PM
Replies: 10
Views: 3,112
Posted By t-mange
Thanks for the explaination Brian! I think...

Thanks for the explaination Brian!

I think I'll reduce it to 0 then, since we kinda have a stop, turn and go kinda track.:lol:

Thanks for the help from all of you guys, I love this forum.
Forum: Brushless 06.03.2009, 03:47 PM
Replies: 10
Views: 3,112
Posted By t-mange
Ok, the track i'm runing at is a mix of lose dirt...

Ok, the track i'm runing at is a mix of lose dirt and hard packed/dryed mud.

So, my motor will run cooler with lower punch?
Forum: Brushless 06.03.2009, 03:25 PM
Replies: 10
Views: 3,112
Posted By t-mange
Ok, Thanks. I'll do that, Do you think I...

Ok, Thanks. I'll do that,

Do you think I should raise the punch control to 100?

No, i havenīt dared too go any higher.
Forum: Brushless 06.03.2009, 02:53 PM
Replies: 10
Views: 3,112
Posted By t-mange
In the 150*F zone after 15mins, suruding temp was...

In the 150*F zone after 15mins, suruding temp was like 70.

You think I'm undergeard?
Forum: Brushless 06.03.2009, 02:31 PM
Replies: 10
Views: 3,112
Posted By t-mange
Need help with MMM settings for a cool MedUsa

Hi guys.

What can I change in my MMM settings to lower the motor temp and overall amperege.

Settings now are:

SW: 1.21
Lipo cutoff: 3.2v/cell
Proportional W/ Reverse lockout
Brake...
Forum: Brushless 02.24.2009, 03:35 PM
Replies: 45
Views: 19,428
Posted By t-mange
My setup: Hyper 8.5 MedUsa 36-70-1600 V2 ...

My setup:

Hyper 8.5
MedUsa 36-70-1600 V2
Rhino 5s 4900mah 20c
Gearing 15/46, I can gear higher if i want more speed, but I donīt:lol:
MMM settings, High start power, 100% punch control, lowest...
Forum: Brushless 02.02.2009, 02:24 PM
Replies: 8
Views: 2,994
Posted By t-mange
Maybe you would want to try this motor? ...

Maybe you would want to try this motor?

http://www.hobbycity.com/hobbycity/store/uh_viewItem.asp?idProduct=8477
Forum: Brushless 01.26.2009, 04:48 PM
Replies: 27
Views: 5,729
Posted By t-mange
Na, i plugged all the wires in to the MMM, and...

Na, i plugged all the wires in to the MMM, and then I was going to yank them all out off the mamba(for a photo) when the wire came out, but the bullet didnīt:tongue:, so i resoldered them all, just...
Forum: Brushless 01.26.2009, 03:28 PM
Replies: 27
Views: 5,729
Posted By t-mange
Check the bullets, i got i cold solder joint in...

Check the bullets, i got i cold solder joint in my mmm package NIB.

http://www.vasterortsrc.nu/Portals/0/Gallery/Album/124/IMGP1923.JPG
Forum: Brushless 12.29.2008, 07:31 AM
Replies: 7
Views: 4,214
Posted By t-mange
I have a friend who runs these...

I have a friend who runs these (http://www.hobbycity.com/hobbycity/store/uh_viewItem.asp?idProduct=6540) in his rc18t FT. It works well.
Forum: Brushless 12.18.2008, 11:34 AM
Replies: 7
Views: 4,141
Posted By t-mange
I think he means these...

I think he means these (http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNRA6)
Showing results 1 to 13 of 13

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top