 |
|
|
|
|
|
 |
 |
9918 Installation Question |
 |
|
 |
|
(#1)
|
|
RC-Monster Carbon Fiber
Offline
Posts: 65
Join Date: Feb 2005
Location: Omaha, NE
|
9918 Installation Question -
03.27.2005, 12:15 PM
I've got everything installed on my truck now and I'm getting ready to install the controller, motor, and ubec. Where on the controller is the jumper located that needs to be removed in order to run the ubec externally? I cut the shrink wrap off near the red positive battery lead but I don't see anything.
|
|
|
|
 |
 |
 |
|
|
|
|
|
|
(#2)
|
|
Site Owner
Offline
Posts: 4,915
Join Date: Nov 2004
Location: PA
|
03.27.2005, 12:40 PM
It is near the red programming jumper, under the heat shrink. It is a black "tab" that you simply pull out. It is just below the caps.
|
|
|
|
|
|
|
|
|
|
|
|
|
(#3)
|
|
RC-Monster Carbon Fiber
Offline
Posts: 65
Join Date: Feb 2005
Location: Omaha, NE
|
03.27.2005, 12:43 PM
Is the small black tab connected to the actual circuit board?
|
|
|
|
|
|
|
|
|
|
|
|
|
(#4)
|
|
RC-Monster Carbon Fiber
Offline
Posts: 65
Join Date: Feb 2005
Location: Omaha, NE
|
03.27.2005, 12:44 PM
Nevermind, I'm assuming it's the black tab that I just slid off of the two prongs.
|
|
|
|
|
|
|
|
|
|
|
|
|
(#5)
|
|
RC-Monster Carbon Fiber
Offline
Posts: 65
Join Date: Feb 2005
Location: Omaha, NE
|
03.27.2005, 12:46 PM
Sorry for all the questions Mike, but does the UBEC plug end go over the prongs that I just removed the tab from?
|
|
|
|
|
|
|
|
|
|
|
|
|
(#6)
|
|
Site Owner
Offline
Posts: 4,915
Join Date: Nov 2004
Location: PA
|
03.27.2005, 12:51 PM
The plug on the UBEC plug goes into the receiver. The wires get soldered directly to the battery connections.
|
|
|
|
|
|
|
|
|
|
|
|
|
(#7)
|
|
RC-Monster Carbon Fiber
Offline
Posts: 65
Join Date: Feb 2005
Location: Omaha, NE
|
03.27.2005, 01:43 PM
Do I need to remove any wires from the plug going to the receiver since I'm using the UBEC, or do I just plug it in like it is since I removed the black tab already.
|
|
|
|
|
|
|
|
|
|
|
|
|
(#8)
|
|
Site Owner
Offline
Posts: 4,915
Join Date: Nov 2004
Location: PA
|
03.27.2005, 03:24 PM
Plug and play. No need to remove any of the wires. Removing the BEC jumper is all you need to do.
|
|
|
|
|
|
|
 |
«
Previous Thread
|
Next Thread
»
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Linear Mode
|
|
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com
