9l in crt .5?

anybody run one before.....I want to run just 3s or 2s in this truck...using a mm no bec?

stock spur and I want maybe 40-50 mph

[BrianG]

There are a few who have run that and like it. Stays relatively cool considering it's a Feigao. But, if you run 3s you should still use a BEC IMO...

Originally Posted by BrianG

There are a few who have run that and like it. Stays relatively cool considering it's a Feigao. But, if you run 3s you should still use a BEC IMO...

I will use a bec than .......what pinion would you suggest and its mod1 correct?

[BrianG]

Pinion depends on speed you want really. And yes, it's mod1...

well I tried to use the calculater but it didnt have a choice for a crt .5 spur
and I dont know how many teeth are on a stock crt .5....I know I know go count the teeth.....to lazy right now

crt.5 spur, is the same as 1/8 buggy standard spur, 46t.
And if you want my 1509, 2.5d/s (2700Kv), i can sell it................

Originally Posted by david lamontagn

crt.5 spur, is the same as 1/8 buggy standard spur, 46t.
And if you want my 1509, 2.5d/s (2700Kv), i can sell it................

oh yes I offered you a trade....but I just sent a pm for price


the 9l is about the same kv and a heck of a lot cheaper but I know the neu is much better quality

i ran the calc with 46 spur and I cant hardly get it below 65mph....lol....you would need like a 10t

[BrianG]

65mph? What settings did you enter?

Differential Ratio: 3.25
Transmission Ratio: 1
Other Ratio: 1
Spur Tooth Count: 46
Pinion Tooth Count: 14
Total Voltage: 11.1
Motor KV: 2731
Tire Diameter (inches): 4
Tire Ballooning (inches): 0
Spur/Pinion Ratio: 3.29 : 1
Total Ratio: 10.67857 : 1
Tire Circumference (inches): 12.57 inches (319.19 mm)
Total Motor Speed: 30314.1 RPM
Vehicle Speed: 33.78 mph (54.26 km/h)
Estimated Adjusted Speed: 32 mph (52 km/h) - 4% loss

lol....I see what I was doing wrong....i was entering 1/1 for diff's

btw there was no stock spur at 46t...you sure its not 48t?

Originally Posted by BrianG

65mph? What settings did you enter?

Differential Ratio: 3.25
Transmission Ratio: 1
Other Ratio: 1
Spur Tooth Count: 46
Pinion Tooth Count: 14
Total Voltage: 11.1
Motor KV: 2731
Tire Diameter (inches): 4
Tire Ballooning (inches): 0
Spur/Pinion Ratio: 3.29 : 1
Total Ratio: 10.67857 : 1
Tire Circumference (inches): 12.57 inches (319.19 mm)
Total Motor Speed: 30314.1 RPM
Vehicle Speed: 33.78 mph (54.26 km/h)
Estimated Adjusted Speed: 32 mph (52 km/h) - 4% loss

[BrianG]

The stock spur on mine is definitely 46t...

The stock tires diameter on the crt.5 is not 4.0, but 3.5

The spur is 46 yes

The 9L runs pretty nice. Has good power, runs pretty darn cool also.

But if you can swing that Neu, DO IT!

And 4 in is std 2.2 truck dia, so 3.5 is buggy. Depends on what he is running

Originally Posted by BrianG

The stock spur on mine is definitely 46t...

btw there was no stock spur in the pull down at 46t...you sure its not 48t?

hint hint

My crt.5 will have my Neu 1512, 1.5d/s on 4s, with proline bowtie 30 serie.
SHould be nice setup for bashing

[BrianG]

Originally Posted by bustitup

hint hint

It's not listed under Ofna because the ones there are "specialty". At the top, right under Miscellaneous, is the 46T spur.