New castle brusless system?

[revo madnesss]

It seams ay cadtle just realised a new brushless system for short course http://www3.towerhobbies.com/cgi-bin...?&I=LXAETT&P=7

Although it's not on the castle web sure yet so can this be accsudently leaked by tower?

If not there is a typo in the max voltage as it says a lip is 4.8v

[nitrostarter]

CC stated a while back they were developing a SC setup.

[molak]

Seems like a MMP without the fan. As the ESC castle makes for HPI

http://www.hpiracing.com/products/en/1151/

[DCastaneda]

Originally Posted by molak

Seems like a MMP without the fan. As the ESC castle makes for HPI

http://www.hpiracing.com/products/en/1151/

That's a sidewinder in the HPI link as is the new combo with the 1410 motor.

[ZippyBasher]

That is a great combo... Affordable 540 size 4-Pole motor. Way To Go Castle!!!! I am adding this to cart now in case the price goes up...

I Actually believe the Tower link is a MMPro... It says 25v Max Input... but could be wrong...

[whitrzac]

Originally Posted by ZippyBasher

That is a great combo... Affordable 540 size 4-Pole motor. Way To Go Castle!!!! I am adding this to cart now in case the price goes up...

I Actually believe the Tower link is a MMPro... It says 25v Max Input... but could be wrong...

no, look at the wires, it is a sidewinder...

moor sizes of 14** motors please maybe a few sensored ones??

[nitrostarter]

Originally Posted by whitrzac

no, look at the wires, it is a sidewinder...

moor sizes of 14** motors please maybe a few sensored ones??

I agree, its a beefed Sidewinder. A MMP would drive the price to around $150 or higher.

[Thomas Porfert]

Originally Posted by ZippyBasher

That is a great combo... Affordable 540 size 4-Pole motor. Way To Go Castle!!!! I am adding this to cart now in case the price goes up...

I Actually believe the Tower link is a MMPro... It says 25v Max Input... but could be wrong...

I believe this is a misprint, I'll have to double check with the engineers, but I'm pretty sure this is a misprint. That combo is only designed to run on a 2s LiPo.

Originally Posted by alport

There is something wrong. 1409 is 57mm long but on towerhobbies 1410 motor is 53mm long

Remember the **09 vs **10 is the length of the stator inside the motor, not the length of the motor itself. Like ta_man mentioned, I believe we have reduced the spacing inside the motor and fit more into a smaller package. I'll double check one with a pair of calps and find out for sure.

Thomas Porfert
Castle Tech Support

[Kcaz25]

I'm excited to see the 1410!

[suicideneil]

I guess that was the topsecret motor Patrick couldnt talk about back along- 4 pole vxl replacement anyone?

[BrianG]

It would be nice if CC could make all of their motors so that a sensor "plate" could be attached to their current motors...

[TexasSP]

A big Hell Yeah for castle. Nice to see some smaller potent motors coming into the market that don't cost and arm and leg, and a 25 volt sidewinder to boot!

There is something wrong. 1409 is 57mm long but on towerhobbies 1410 motor is 53mm long

[ta_man]

Originally Posted by alport

There is something wrong. 1409 is 57mm long but on towerhobbies 1410 motor is 53mm long

Not necessarily something wrong. If you have ever owned a Neu motor you would know there is a lot of empty space at each end of the windings inside the can that is thus included in the dimensions of the can. Castle probably just did away with some of the empty space (especially on the back end).

[crazyjr]

Hey Thomas, Will the motor be available seperately? I have a associated T4 and would like to run that motor