Your opinions please

[GorillaMaxx360]

i have asked many and many questions and have come up with a list of items needed for my emaxx project please comment if you think one or many of these items wont hold up. Also if you want to make any suggestions please do. and i already have a stock E-maxx, Punisher turnbuckles, MSRP5 integy shocks(please dont diss i got them for free), and flextek ti arms. Also if there is anything i should add or remove from this list.
X-Maxx Project

1. G2 X-Brace Chassis - Graphite Kit $198
2. G2 X-Brace Motor Mount Kit $42
3. G3-XL Battery Straps - Black $12
4. G3 Race Skid Plates $39
5. G3 Shock Tower (2) $38
6. G3 Spacers - Full set $9
7. G3 Fasteners - Full set $12
8. Front and Rear Hybrid Bulks $140
9. HB Lightning Diffs (2) $130
10. FLM maxx front and rear bulkhead braces $18
11. RC Monster slippererential $200
12. Super Maxx servo saver kit $84
13. Super Maxx titanium pivot Balls (8) $44
14. Super Maxx knuckles (2pair) $102
15. Front bumper RPM - black $9
16. Super Maxx 8mm CVDs $112
17. T-Bonz Hardened Steel Center CV Drive $30
18. Maxx black oxide hex head screw kit $26
19. Integy Front Bumper Set (Silver) (F and R) $42
20. Titanium bead lock rims Ti22inc. - Gray $130
21. Proline badlands (2 pair) $ 62
22. Proline ultra foam inserts (2 pair) $18
23. Spectrum DX2.0 radio $169
24. Hitec 5955TG titanium gear servo $125
25. Atomic Racing F150 - black w/white flames $35
26. Quark 125B ESC $280
27. Super brain Charger $120
28. Team associated black grease $8
29. 8000 mah batteries Lipo $230
30. Feigao 7xl brush less motor $90

[sjcrss]

17. T-Bonz Hardened Steel Center CV Drive $30
you won't need this, because the slipperential will have center driveshafts that come with it....other than that looks pretty good, but you did forget about the LBA10 lipo balancer from maxamps.com..that costs $49.95

[GorillaMaxx360]

what is a balncer
is it like a charger or what why so expensive 100 bucks for two

[sjcrss]

you only need one to balancer your cells.... see this thread...it will help....it is for the LBA6 balancer, but the LBA10 is better...it is 7 pages long...but has alot of info on what you ask..page 3 has alot of good info as well

http://www.rc-monster.com/forum/showthread.php?t=3971

[jhautz]

Sounds like it will be a sweet setup.

If you are dropping that much cash at once, I would upgrade the motor to the Nue 1515/1Y. It would be just about the same KV as the 7xl, but much more efficient and run much cooler. I would also add the Quark heatsink to the list. The With a high KV motor like that the quark will need the extra cooling.

Both of these are worth investment into a stable cool running brushless system.

Originally Posted by jhautz

If you are dropping that much cash at once, I would upgrade the motor to the Nue 1515/1Y. It would be just about the same KV as the 7xl, but much more efficient and run much cooler.

I agree. My 7xl would get pretty hot after 7 minutes or so.

[smhertzog]

An 8XL would be a much cheaper alternative. A Neu would be nice but you could buy three 8XL's for the price of one Neu.:032:

[neweuser]

Also, make sure you get the right HB diffs that fit the Hybrids...