Lipo repair - Page 11 - RC-Monster Forums

lincpimp · 03.19.2009, 01:59 PM

Quote:

Originally Posted by mjderstine

those looks great. to bad you cant turn the packs i sent you into those :) but then again, that would be a real magic trick to get thatdone. i know what you mean about projects, i have a crawler and a mp7.5 on the bench in pieces!

nice lookin batts

Thanks!

If I could change battery ttpes I have a feeling maxamps would be knocking my door down!!!

mjderstine · 03.19.2009, 03:21 PM

no doubt sir. an a few other people to boot.
alright sorry for the topic straying...

suicideneil · 03.19.2009, 04:05 PM

This is RC-Monster- if we dont go off topic I'd be worried...

mjderstine · 03.19.2009, 04:07 PM

good to know you guys can be lax about that, some forums ct your fingers off if you get off topic !

lincpimp · 03.19.2009, 04:12 PM

Quote:

Originally Posted by suicideneil

This is RC-Monster- if we don't go off topic I'd be worried...

Very true Neil, and it is usually my fault that threads go astray...

Quote:

Originally Posted by mjderstine

good to know you guys can be lax about that, some forums cut your fingers off if you get off topic !

Yeah, some people have no sense of humor!!!

03.24.2009, 05:20 PM

Subscribed- Linc does great work!

Metallover · 03.27.2009, 12:19 AM

Is there any way I could get a label made for my 3s 30c 3200 flightpower? I posted a thread on it... Also could you send me pm with the price to re-build my flightpower linc? I forgot how much it was... I'm just thinking about re-doing it...

lincpimp · 03.27.2009, 02:53 AM

Quote:

Originally Posted by Metallover

Is there any way I could get a label made for my 3s 30c 3200 flightpower? I posted a thread on it... Also could you send me pm with the price to re-build my flightpower linc? I forgot how much it was... I'm just thinking about re-doing it...

ok, a little more info on the pack and problem would be handy...

Metallover · 03.27.2009, 10:20 AM

Quote:

Originally Posted by lincpimp

ok, a little more info on the pack and problem would be handy...

I don't know if you remember the pack I got from takedown and I was going to finish it myself... It was basically three cells hooked together and I put wires on it. I would want you to take all the wires off and put new leads on with astro taps and deans, then shrink er together and send it back. Let me know if you need any more information. The wiring is in... Rough shape now.

himalaya · 04.01.2009, 05:44 AM

Quote:

Originally Posted by lincpimp

Also I will list the brands of lipos I have already repaired, and should not have any trouble with.

Any enerland cell based pack (ie, polyquest, polyrc, flightpower, neuenergy, hyperion, etc)

Maxamps (all)

Hi Linc, are Neuenergy Packs actually using Enerland cells? Note their capacity numbers are completely different to the ones listed on Enerland's website for their XP XQ cells.

lincpimp · 04.01.2009, 11:36 AM

Quote:

Originally Posted by himalaya

Hi Linc, are Neuenergy Packs actually using Enerland cells? Note their capacity numbers are completely different to the ones listed on Enerland's website for their XP XQ cells.

I always thought they were enerland. They are assembled similar from the outside, and they definitely have tabs on each end, and only enerland and elite do that.

I have not pulled any neu packs apart yet, no dead cells so far.

In fact I have not dealt with an enerland based pack that had anything other than physical damage, no qc issues, tabs falling off or much else.

I did have one trakpower pack that smoked a bit during a charge, turned out a balancer wire must have been bad (maybe pinched and cut thru most of the strands?), and it got hot and melted the insulation. I popped it open and changed the wire out, no issues since...

Otherwise my experience with enerland cells has been great. I have made and reconfigured a ton of packs by them, with great results.

magman · 04.01.2009, 10:00 PM

I forgot to post this earlier in the week...

I had the pimp do some mods to a couple of my batts....and I am happy to report that he did a professional job. The manufactures could take a lesson or 2 from him on wrapping batteries.

Thanks...another satisfied customer!

brushlessboy16 · 04.01.2009, 10:04 PM

Any word on those 2s hardcased rcm's linc ;)

rawfuls · 04.01.2009, 10:07 PM

Any experience of making a hard case for a lipo Linc?

slimthelineman · 04.01.2009, 10:22 PM

hey linc, ever tried to replace a tab on a neu cell? i have a couple lying around, is there hope? the cells are in excelent shape other than the damaged tabs.