RC-Monster Forums  

Go Back   RC-Monster Forums > RC-Monster Area > General Discussion

Reply
 
Thread Tools Rate Thread Display Modes
Old
  (#1)
t-maxxracer32
RC-Monster Brushless
 
t-maxxracer32's Avatar
 
Offline
Posts: 2,184
Join Date: Nov 2006
01.22.2010, 03:35 PM

well the volts on it are right and when running it for the few minutes it works it does have power.

but ill try what you said
   
Reply With Quote
Old
  (#2)
sikeston34m
RC-Monster Brushless
 
sikeston34m's Avatar
 
Offline
Posts: 2,085
Join Date: Sep 2007
01.22.2010, 09:26 PM

Quote:
Originally Posted by t-maxxracer32 View Post
well the volts on it are right and when running it for the few minutes it works it does have power.

but ill try what you said
I've been thinking about this entire problem, and something just doesn't sound right.

Then it hit me!

Go into the setup for your ESC and change your Low Voltage Cutout to 2.2 to 2.4 volts per cell.

Your ESC is still setup for regular LIPO!
   
Reply With Quote
Old
  (#3)
t-maxxracer32
RC-Monster Brushless
 
t-maxxracer32's Avatar
 
Offline
Posts: 2,184
Join Date: Nov 2006
01.23.2010, 02:24 AM

Quote:
Originally Posted by sikeston34m View Post
I've been thinking about this entire problem, and something just doesn't sound right.

Then it hit me!

Go into the setup for your ESC and change your Low Voltage Cutout to 2.2 to 2.4 volts per cell.

Your ESC is still setup for regular LIPO!
you were right it was set to cutoff at 6.2V

would have never thought about that..

I hope that works but its not as if it cuts off immediately. the batteries just have no power...

ill give it a try right now n see whatsup.

thanks
   
Reply With Quote
Old
  (#4)
sikeston34m
RC-Monster Brushless
 
sikeston34m's Avatar
 
Offline
Posts: 2,085
Join Date: Sep 2007
01.23.2010, 02:43 AM

Quote:
Originally Posted by t-maxxracer32 View Post
you were right it was set to cutoff at 6.2V

would have never thought about that..

I hope that works but its not as if it cuts off immediately. the batteries just have no power...

ill give it a try right now n see whatsup.

thanks
You should see what that's doing on an Eagletree.

The ESC will limit or shut off amp draw at or below the LVC setting. (goes dead)

Stand back folks! It's getting new life breathed into it! LOL

I'm sure it will run fine now.

I don't know what your setup is, but the Lifepo4 cells will hold about 2.8 volts per cell under 100 amp load.

2.8 volts per cell is well below where you had the LVC set at.

Yeah it's gonna run for a few minutes, but the ESC will limit amp draw at the LVC setting of 3.1 volts per cell.

The amount of the limitation is whatever the battery will push out before the 3.1 LVC setting. Which may only be 30 amps or so.

Last edited by sikeston34m; 01.23.2010 at 03:03 AM.
   
Reply With Quote
Old
  (#5)
_paralyzed_
working on a brushless for my wheelchair.....
 
_paralyzed_'s Avatar
 
Offline
Posts: 4,890
Join Date: Mar 2007
Location: minnesnowta
01.23.2010, 02:57 AM

damn sike, good thinking. makes perfect sense now that I read it.


_______________________________________

It's "Dr. _paralyzed_" actually. Not like with a PhD, but Doctor like in Dr. Pepper.
   
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump







Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com