Muggy diffs in a maxx

[its me]

Originally Posted by suicideneil

http://www.allerc.com/index.php?cPat...ba8c5f9b7c427f

On that page, scroll down a little. I've never seen so many chargers and cable adaptors etc- should have all that you need.

thanks man, that helped alot



mriccucci- from center of front diff to rear diff just a little over 15 inches, total truck length from front to back almost 19 inches. Yes its long but what I learned from the nitro twin is that length means stability at high speeds.

Shocks are jammin big bores.

[its me]

WOOOOOOHOOOOO!!

My buddy bill hooked up a smoken deal on these MOFO"S!

[jayjay283]

Wish I was a friend of Bill

[jnev]

Damn!! That thing'll rip! You mind introducing Bill to me?

[JERRY2KONE]

Dude that is one awsome ride you have put together there. It looked pretty great what you started with, but every time you post up new photos and we get to see a little bit more. That is a great work of art that you have created. Congeratulations on those battery packs as well. That is one cool friend you have there. Now get that thing finished and post up some results of your hard work. Way to go itsme.

[mriccucci]

all i can say is this thing looks amazing keep up the good work. I picked up some 1/8" 6061 yesterday from a local place. Im going to hopefully start work today or tomorrow on it.

[its me]

Thank you guys!! I cant wait to see this thing run aswell!

[mriccucci]

Keep up the good work man. I got some drive shafts yesterday and got everything together today but i think im a little long. My main purpose was to run my truck in the truggy class but im a little over 16" wheel base with just about 23" overall length. What driveshafts did you use It's me?



I was also wondering if you have some shputs of how you ran the steering setup?

[mriccucci]

Ok so no need for the driveshafts i got a muggy center shaft, and im using a muggy front cv for the front center. Puts my wheelbase right around 14.5-14.75" I started mocking everything up and will hopefully be running by next weekend.

[suicideneil]

http://cgi.ebay.com/T-MAXX-DOMINATOR...QQcmdZViewItem If you fancy a massive short cut....

[mriccucci]

Well no need for that now, all i have to do is decide on braces and a chassis width. I have the main part of the chassis laid out with the centerdiff and front and rear bulks in place.

[_paralyzed_]

its me or mricucci- any progress? I've been watching!

[its me]

Originally Posted by _paralyzed_

its me or mricucci- any progress? I've been watching!

LOL im almost done, all I need are the monster maxes. I need one to get the foot print so I can cut some carbon for its tray, after I do that then most of the parts are going to MRpaintin.com to get black anoed. Only the diffs and chassis are going to stay silver :)

EDIT* sample of Matt and Ross's work:)
http://www.rc-monster.com/forum/show...502#post164502

[mriccucci]

Originally Posted by _paralyzed_

its me or mricucci- any progress? I've been watching!

I've also been busy, im deffinatly not very good with the jigsaw and dremal but i think i may be able to get a local guy to laser cut another chassis plate.





My plan is to make some plates to go from the braces to the bulkheads like its me did. I think i may extend them a little on each side. Im going to cut the chassis dont a lot more, prolly about 5-7 inches wide. I've got 14.5 inches of wheel base so im just about at the truggy lenght. The only thing i need now is to find a body that would fit.

[_paralyzed_]

looking good