12020 Question
 

There is a lot of wires coming off of this thing, 6 blue ones and two black and two red. could someone tell me what to do with all these and where to solder them?

Just treat the pairs as if they were one wire!
You'll get 3 motor wire pairs, and a black pair and a red pair.

I take it you have some experience with BL, so I wont type the whole story. But feel free to ask if you get a problem.

actually i have NO experience with BL just my mamba. what are th eblue wires for?

the blue wires go to the motor. there is 6 and there in pairs. just solder the female connectors to the motor wires and the male connectors to the blue wires.

http://www.rc-monster.com/forum/show...5&pagenumber=2

theres a picture of mine all wired up.

can you send me a full size pic to vwghiadude@Hotmail.com

Just wire each pair of bleu wires to a motor lead. Order is not relevant.

And wire your cells between the Black and Red pair. If you use 2 packs, wire in a way so that all cells are in series.

ok, how come it is two wires to each motor lead?

i know how to wire it all now. next step is BATTERIES. Yay

lol! u jumped into a 12020 without a 9920 first! lol, have fun bro!

I will, i am trying to find a spot to momunt the ESC right now though, it is kind of hard

i might need to mount it on the outside of the TVP for now, there is NO room at all,

here this picture might help with the wiring.

toby, I would keep the ESC on the inside of the TVPs. Or when you want to put it on the outside, make a cover.

Did you get a warrior or micro, btw?

warrior, i cannot find any room for it on the inside, so i dunno where to mount it

Does the 9920 have 6 wires like that? Where they need to be paired for the motor? If so I need more connectors! Might just direct solder them...

i am going to direct solder them to the motr, can i cut the blue wires down a bit?

Yes, you can shorten the blue wires, no problem. But leave the motor wires as they are.

yes, the 9920 has 6 blue wires. all you do is solder the pair into one connector. so all your gonna need is 3 male and 3 female.

i was just going to direct solder two wires to one motor lead. and then the next two to another etc.

i would suggest using connectors.

like deans? and if so how do you solder one dean to one wire?

no, i would use 3.5mm connectors. http://www.rc-monster.com/products.php?cat=21&pg=2

i would use deans on the batteries.

i have NO time to order it, so i guess direct solder is my only choice

Same here, I have bullet connectors but I don't think I can fit 2 wires in one, unless I solder one wire further down the other? Best to direct solder?

Mike told me to direct solder

actually the dual wires fit quite easily. i didnt have any trouble.

Toby where did you get the 12020? are they warrior or micro??

Mike sells them here of course!

Can you let Toby answer the questions? I just want to know whether he got the Warrior 12020 from Mike or from somewhere else.

i got it from here and it is warrior

I thought they are out of stock..I want the warrior tooo... :( Mike, when are they going to be available again??

The warriors(9920 and 12020) should both be back in stock(with Plenty) within a couple weeks.
The 9920 controllers usually have only one set of wires(thick), but some have had two sets. the recent ones had one set, though(Nick). The 120 amp and larger controllers have the double wire.

So do you mean that I missed the 1st shipment :(?? Ive signed up for the notice but didnt get any msg from rc-monster.com. So Mike can you put me on the list for the next shipment?? Not going to miss them again.

By the way do you have the Wanderer in stock?? If not are they going to come with the Warrior?

Wanderers will be along with the warriors. If you recently signed up for notification, you haven't missed anything. The 9920s, 12020s, and a few wanderer motors will be along soon. I should have enough to go around this time!

okay, i need a straight answer, no beating around the bush.

Those blue wires, first

why is there two to each wire lead.
does it matter which two go to which motor lead?

it matters to a point. If you keep the wires in pairs like coming out the esc you fine. That should give you the sets to connect to the three wires of motor. that part does not matter fat as which set to each wire of motor.

so as long as the blue wires stay in the pairs they are they can go to any lead? i am still trying to find somewhere to mount this thing

yeah toby. If the motor spins backwards to the way you need it. Swap two of the three wires and it will be right.

umm, i am direct soldering though, kind of a difficult thing to do, there is no way to do it right the first tiem? and how would i know which wires to swap?

Any two wire of the three will work. It does not matter.

also, if your direct soldiering you can always do it another way. all you have to do is have the batteries plugged in and pull the red programming jumper off and then if it beeps that is telling you that it is switched directions. then just put it back on.