Testing a New Type of Motor
 

Ok guys I talked it over with brianG and hopefully the thread wont get deleted this time. :yes: I will be testing some motors coming up soon. As I had said before. Here are the specs, notice somethings have been changed.:yes:

Specs

Size- 44mm x 73mm
KV Rating- 1500 to 2100.
Poles- HQ 2-pole
Internal Resistance- To be determined...


Features

Kevlar wrapped rotor, rotor will be reinforced with dual supports on lower and upper shaft, shimmed rotor, 100k rpm ceramic bearings, finished bonded rotor, 12awg low resistance wires, 5.5mm plugs, motor will be all jet black color including black wires, will be finned can, HQ 2-pole design, removable rear endbell, will be rebuildable, high strength neodymium rotor with a rating of n38-n45, high quality windings which offer super low resistance.

The company has shipped out the cans and endbells along with the shaft. We are still looking to order the neodymium magnet and outer can magnets along with the windings and high quality bearings. Once some of the stuff arrives, I will post pics threwout the motor's build.:party:

N50! N50!!! :lol:

Sounds really cool. I will be keeping an eye on this thread. Can you build me a 550-size motor that will survive at 100K rpm? Maybe use a titanium braid-wrapped rotor? :smile:

I was looking at the highest quality Neo but I think Ill stick around with what neu, lehner and hacker use which is around the n40ish range if I remember correctly. And for right now I am not building motors for anyone. Trying atleast get mine done.:lol:

Ehhh, I do recall that the "weaker" grades of NdFeB can take more heat. So I guess that's OK. :mdr:

Sounds cool. I will be watching.

I think you forgot that you have a partner here...:intello: That'd be me! No lie either, we're doing this together, thug.:lol: This should be an exciting experiment, and hopefully turns out good.

I thought I was dreaming last night as I was reading about this great new motor you guys are working on and then poof it was gone. I will watch this one to see how it goes. Sounds pretty cool.

As long as this thread is basically an "R&D" type of thread, I don't think the power that be will mind. But I would strongly advise to avoid making this thread seem like it will even possibly become a sales item. And it would be bad form to get all kinds of feedback/suggestions/etc here and then go elsewhere to sell them.

If this thread disappears again, it will most likely be the Monster that did it and would refrain from starting another one.

That said, it will be interesting to see what kind of results you get (and maybe how many ESCs burn out testing them :wink:)

Hopefully none... lol

Haha, were hopefully going to avoid that alltoghther.:lol:

Just to let you guys know. Our first couple motors that we will be testing will be 2-pole just to see how far that will get us.:yes:

I'm curious, are you doing this to save money, to make a more powerful motor, or just to do it? Either way I will appreciate what I learn. Lotsa pics please!

Were doing it because were curious what a 2-pole of this kind of build will be capable of.:yes: Yes pics will be posted threwout the build.:party:

pretty ambitious, I have a hard enough time keeping my r/c's in one piece

Haha were hoping to destroy some tranny's.:yes::lol:

sounds cool. maybe u guys can supply me with a motor, lincpimp can give me and ESC and i can do a T-maxx conversion!!

Q. Does this company sell complete motors of various specs, or are you just buying the parts to build your own motors like you can with some outrunners (kit form) for experimentation's sake?

Were are not selling motors.:whistle:

...i said give, not buy lol. i could be ur lab rat

Haha....:rofl:

Wut would a rat do with a brushless motor?? We'll be sure to ship you out a nice fat piece of Wisconsin Cheddar.:rofl:

Lmao, That could be our added bonus!:rofl::party:

People will know for sure where our motors are coming from that way! include a free slice of cheese and free bottle of beer.:party:

Haha tru dat!

Oh, btw. We card...:lol:

Oh, thats no problem.


I have Neils ID right here.

http://i87.photobucket.com/albums/k1...eilmclovin.jpg


I have been waiting for a good opportunity to use this!:lol:

Hahahhahah! How long have you had that waiting....?

Haha nice!

lmfao!! Nice!!! You pass.

I went lookin through his photobucket awhile back and saw that pic. It made me laugh. I just decided to add it to the license today when I saw the "checkin I.D." thing.

neil's gonna kill me....:oops:


:rofl:

o man that funny!!! Anyways, ya, i could your 'factory driver' and for lincpimp also. u send me the electronics and i help test and work out the bugs

You got my D.O.B wrong, and my weight....

...? lol

the pic on the I.D.

Its a pic of suicideneil.

I never changed the info on the I.D. when I pasted his pic on there.

oh well......its still funny :party:

OK guys Ive got some possible good news. We ended up having a discussion with the guy who is making the can, endbells and rotor for us. He is willing to make us some larger cans aswell. We are thinking 8mm shafts, 60mm in width, 120mm in length with a 35mm x 80mm neodym magnet. Wouldnt know what kv's to choose yet though.

I am not making any guarentees though...

hot sex that'd push a Maxx around

Haha, it would destroy anything smaller than a 1/5.

...IM DOWN!!!! lol

Calm down!:rofl: