RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: mrsnuggles
Forum: HPI Savage 02.28.2011, 09:15 PM
Replies: 350
Views: 165,174
Posted By mrsnuggles
it might damage the pin holes and the rear brace...

it might damage the pin holes and the rear brace if it fails, no matter what material they are made of as of the high leverage and the pin strength.

here are pic's from my 2007 setup....
Forum: HPI Savage 02.28.2011, 08:47 PM
Replies: 350
Views: 165,174
Posted By mrsnuggles
the screws that hold the rear brace and pin...

the screws that hold the rear brace and pin keeper are in danger of getting pulled off as your wheel gets snagged by something. the brace in front is not enough to keep your arm from getting pulled...
Forum: HPI Savage 02.25.2011, 09:46 PM
Replies: 130
Views: 131,698
Posted By mrsnuggles
actually he is a copy cat. he just copyed my...

actually he is a copy cat. he just copyed my product, bashcatrc bulkhead braces, he just made some tweaks to the design. one piece was even a direct copy, but i got him to change the design enough so...
Forum: HPI Savage 02.17.2011, 07:16 PM
Replies: 41
Views: 22,014
Posted By mrsnuggles
oooh shiny, can't stop staring. are these...

oooh shiny, can't stop staring.

are these aluminum bulks quick access like the x bulkheads?
Forum: HPI Savage 02.17.2011, 04:40 AM
Replies: 41
Views: 22,014
Posted By mrsnuggles
hehe aluminum bulks and bashcat braces. talk...

hehe aluminum bulks and bashcat braces.

talk about overkill bulletproofing.:party:
Forum: Brushless 05.02.2010, 10:12 AM
Replies: 42
Views: 34,225
Posted By mrsnuggles
i talked to steve neu and he said it would be no...

i talked to steve neu and he said it would be no problem making a 1900 series inrunner with shaft extending through both ends in 8 mm

i'm planning a direct drive myself and my calculations are...
Forum: Brushless 05.29.2009, 01:04 PM
Replies: 18
Views: 3,984
Posted By mrsnuggles
do you guys know of an esc that is capable of...

do you guys know of an esc that is capable of 8-10s that also has brakes and reverse?
Forum: Brushless 05.28.2009, 06:28 PM
Replies: 18
Views: 3,984
Posted By mrsnuggles
here is my idea of using dual 1500 kv motors...

here is my idea of using dual 1500 kv motors connected through a differential so they can each run at their own pace at the same esc settings but still give all they got to the wheels.
gearing is...
Forum: Brushless 05.27.2009, 04:40 PM
Replies: 18
Views: 3,984
Posted By mrsnuggles
i think one of the biggest problem was that it...

i think one of the biggest problem was that it was way over geared as i never used but maybe half the speed of what it was geared for.

the reason i have been thinking about going dual mmm and...
Forum: Brushless 05.27.2009, 04:22 PM
Replies: 18
Views: 3,984
Posted By mrsnuggles
the setup savage xl neu 1515/1y mmm v3...

the setup

savage xl
neu 1515/1y
mmm v3
polyrc lipo 2s and 3s 4900 mah 25c in series for 5s out

15t pinion 52t spur
gearbox locked in second gear(same gearing as the flux)
cen diffs 2.88...
Forum: Brushless 05.27.2009, 03:40 PM
Replies: 18
Views: 3,984
Posted By mrsnuggles
dual esc/motor setup

as i have been frying one mmm after another i was wondering if i could install dual setup in my truck?

i have no problem fitting all the stuff but i was wondering if it could be simple as using y...
Showing results 1 to 11 of 11

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top