RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 15 of 15
Search took 0.01 seconds. Search: Posts Made By: jahno30
Forum: Team Tekin 10.05.2010, 08:54 PM
Replies: 21
Views: 14,578
Posted By jahno30
Randy, The Rotor finally showed up...

Randy,
The Rotor finally showed up today :party:

I installed it & the animal is back to herself :whistle:

Thanks again david....
Forum: Team Tekin 08.19.2010, 01:00 PM
Replies: 21
Views: 14,578
Posted By jahno30
E-mail sent with requested info.... Thanks Randy...

E-mail sent with requested info.... Thanks Randy :party:
Forum: Team Tekin 08.19.2010, 12:09 PM
Replies: 21
Views: 14,578
Posted By jahno30
Okkk..... Sent E-mail to Tekin Support Re:...

Okkk..... Sent E-mail to Tekin Support Re: getting a replacement V2 Rotor for my original "still No response :diablo:" re-glued original rotor & put it back in the motor, & ran it but it got hot...
Forum: Team Tekin 07.12.2010, 05:27 PM
Replies: 21
Views: 14,578
Posted By jahno30
I've been running my RX8 1700kv combo with the...

I've been running my RX8 1700kv combo with the original V1 in my Mugen MBX5 on 6s for almost a year now... It just failed :diablo: I cleaned it up with acetone & stuck it back with jB Weld should be...
Forum: Brushless 03.08.2009, 03:35 PM
Replies: 151
Views: 80,268
Posted By jahno30
I am looking to race against the other nitro...

I am looking to race against the other nitro 1/8's ...
We only have a short 150- 180 foot strait away the rest is technical really a 1/10th track thats been extended slihtly.....
Do you think a 4S...
Forum: Brushless 03.07.2009, 08:55 PM
Replies: 7
Views: 4,152
Posted By jahno30
Is that correct, you got more run time with the...

Is that correct, you got more run time with the 4S ?
Forum: Brushless 03.04.2009, 02:09 PM
Replies: 151
Views: 80,268
Posted By jahno30
I was thinking about using some 6mm carbonfiber,...

I was thinking about using some 6mm carbonfiber, plastic, or plaxiglass flat spacers under the 5xscrews that hold the radio plate to give the additional height required and use plastic spacers on the...
Forum: Brushless 03.03.2009, 08:38 PM
Replies: 151
Views: 80,268
Posted By jahno30
Hey guys.... I too am doing a 1/8 conversion.. ...

Hey guys....
I too am doing a 1/8 conversion..

I have the power racing X8and was considerring the CC 2650 combo , but am unsure as to where to get a single gear conversion and also if a 4S 25c...
Forum: Castle Creations 03.03.2009, 03:14 PM
Replies: 9
Views: 3,153
Posted By jahno30
If this is the case, then what do us new B's need...

If this is the case, then what do us new B's need to be doing to get a set up to run for 20-30 mins without blowing something up...
Forum: Castle Creations 03.03.2009, 02:58 PM
Replies: 50
Views: 13,877
Posted By jahno30
sounds good.... How much run time are you getting...

sounds good.... How much run time are you getting with the 5000ah pack
Forum: Castle Creations 03.02.2009, 08:41 PM
Replies: 50
Views: 13,877
Posted By jahno30
Any update on how the 2650 CC combo ran......

Any update on how the 2650 CC combo ran... curious about any heat issues and also the amount of milliamps been pulled
Forum: Brushless 02.27.2009, 12:09 PM
Replies: 26
Views: 7,856
Posted By jahno30
this might work for you

your best uption would be to try and use an onroad 1/8 and convert that to brushless ...... sick speeds and may even match the 1/10 for excelleration.

I have 2x of the prp's that i'm gonna...
Forum: General Discussion 02.23.2009, 03:27 PM
Replies: 22
Views: 5,112
Posted By jahno30
take a look at the PRP line, I have 2x and am...

take a look at the PRP line, I have 2x and am condsiderring changing them over to the a MMM 2650 combo or the new tekin XR8 combos :party:

http://www.powerracingrc.com/xr8.shtml
Forum: Brushless 11.14.2008, 06:14 PM
Replies: 15
Views: 8,250
Posted By jahno30
Thanks everyone for all your answers. I am...

Thanks everyone for all your answers.

I am looking to get the most play time out of the set up, but still keep the temps down; hence the 6S question.

Lutach, that truggy of yours just makes me...
Forum: Brushless 11.12.2008, 09:10 PM
Replies: 15
Views: 8,250
Posted By jahno30
Lightbulb use of 4S or 5S vs using 6S

Hello all, im new to this electric thing, and have been reading trying to decide which way to go to convert my Mugen mbx5 over to electric.

I think i'm set on the new CC mamba monster 1/8 combo,...
Showing results 1 to 15 of 15

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top