RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 20 of 20
Search took 0.02 seconds. Search: Posts Made By: yj-7
Forum: Brushless 06.06.2007, 05:07 PM
Replies: 2
Views: 4,249
Posted By yj-7
Feigao 540C XL problems

I was running a brand new Feigao 540C XL in my Jammin X1cr buggy and the magnets came loose on the rotor. :035: Has anyone else had this problem? This was only the third time running the motor and...
Forum: Brushless 05.06.2007, 09:53 AM
Replies: 12
Views: 4,274
Posted By yj-7
Thanks for the words of advice hotncold, and I...

Thanks for the words of advice hotncold, and I will probably put velcro on the batts to keep them tight. As for the end of the batts. have you seen Tru RC's packs? They put somthing on the end of...
Forum: Brushless 05.06.2007, 09:46 AM
Replies: 12
Views: 4,274
Posted By yj-7
smhertzog, Thanks for the warning. I was planing...

smhertzog, Thanks for the warning. I was planing on putting a clamp from the end of the motor back to the motor mounting plate to help keep the motor together on landing s from jumping. The motor...
Forum: Brushless 05.05.2007, 08:08 AM
Replies: 12
Views: 4,274
Posted By yj-7
Here is a pic that shows the layout a little...

Here is a pic that shows the layout a little better. One of my goals when I did this project was to leave the center diff where it was and to fit the components around it and still keep a good...
Forum: Brushless 05.04.2007, 09:16 PM
Replies: 12
Views: 4,274
Posted By yj-7
X1CR brushless conversion completed!

Just thought I would post some pics of the completed project. As you will notice in the pics I ended making another motor mount instead of the heatsink one tha I posted in an earlier thread. I also...
Forum: Brushless 04.17.2007, 05:24 PM
Replies: 13
Views: 4,601
Posted By yj-7
And that is the reason that it was done that...

And that is the reason that it was done that way:dft012:
Forum: Brushless 04.17.2007, 04:43 PM
Replies: 13
Views: 4,601
Posted By yj-7
Here are the pics with it in the buggy with...

Here are the pics with it in the buggy with Silent monsters Neu motor.:eek:
Forum: Brushless 04.16.2007, 07:46 PM
Replies: 13
Views: 4,601
Posted By yj-7
Yes, I am a machinist by trade. I also did the...

Yes, I am a machinist by trade. I also did the machining for Silent Monsters MBX5 that is on here.
Forum: Brushless 04.16.2007, 06:38 PM
Replies: 13
Views: 4,601
Posted By yj-7
Heatsink Motor mount/bulk

Just thought I would post a few pics of the motor mount for my Jammin X1CR Pro that I am working on. The motor mount slots are not in yet because I wasnt sure on the spacing.
Forum: Brushless 04.12.2007, 07:03 PM
Replies: 8
Views: 2,951
Posted By yj-7
Does onyone know of other suppliers that have...

Does onyone know of other suppliers that have them in stock?
Forum: Brushless 04.12.2007, 06:10 PM
Replies: 8
Views: 2,951
Posted By yj-7
Lehner 1940 series

Does anyone know when the Lehner 1940 motors will be available again? I am looking for a 1940/7 or 1940/6. I emailed Mike but havent heard anything back yet. I now he is a very busy man so just...
Forum: Buggy 04.07.2007, 07:46 PM
Replies: 50
Views: 23,966
Posted By yj-7
So running a higher voltage lets you choose a...

So running a higher voltage lets you choose a higher kv motor to get the same speed and power output? I'm not sure I understand that. It seems to me like you should run a lower KV for higher volts....
Forum: Brushless 04.07.2007, 07:26 PM
Replies: 12
Views: 3,712
Posted By yj-7
Hey you could just get a bigger flywheel for the...

Hey you could just get a bigger flywheel for the motor you have now:005:
Forum: Buggy 04.07.2007, 02:21 PM
Replies: 50
Views: 23,966
Posted By yj-7
So hows the buggy running? Have you done any...

So hows the buggy running? Have you done any speed runs with it?
Forum: Brushless 04.07.2007, 01:43 PM
Replies: 15
Views: 4,915
Posted By yj-7
Hey Doc, The Jeep is my other hobby. Its all...

Hey Doc, The Jeep is my other hobby. Its all custome built by Silentmonster and me. The engine is tired and it is getting a 4.3 fuel injected v6 to replace the 350 that is in it know. We rock crawl...
Forum: Brushless 04.07.2007, 09:02 AM
Replies: 15
Views: 4,915
Posted By yj-7
Thanks for all the help guys. I'll keep you...

Thanks for all the help guys. I'll keep you posted on how things are going.
Forum: Brushless 04.06.2007, 05:14 PM
Replies: 15
Views: 4,915
Posted By yj-7
Serum, Do you have a link for trakpower packs? ...

Serum, Do you have a link for trakpower packs? Thanks
Forum: Brushless 04.06.2007, 05:05 PM
Replies: 15
Views: 4,915
Posted By yj-7
Chris told me on the phone that I would need to...

Chris told me on the phone that I would need to buy his motor clamp mounts and when I told him I was a machinist and would be making my own motor mount and batt. tray he ended the conversation rather...
Forum: Brushless 04.06.2007, 04:34 PM
Replies: 15
Views: 4,915
Posted By yj-7
XLT 4 motor

Hi all,
I am new to the forum and have some questions for all of you that are knowledgable about 1/8 buggy conversions. I am converting a Jammin X1 CR Pro and will be using the MM controller...
Forum: Buggy 03.28.2007, 03:39 PM
Replies: 81
Views: 29,547
Posted By yj-7
How about the steering servo? It doesnt look like...

How about the steering servo? It doesnt look like there is enough room for the servo?
Showing results 1 to 20 of 20

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top