Who Still Has a Working MMM 'V1'

[DRIFT_BUGGY]

Just wondering who still has a working MMM V1 and what Firmware you are running? I have only changed the settings on the ESC, I have never updated the Firmware from what it is out of the box

[JerryF504]

I have a working v1 with the original v1.17 firmware and a working v2 with v1.19 firmware.

[hootie7159]

i've got one as well...my MMMv1 is in my 8ight w/ updated firmware.....my MMMv2 is working as well in my muggy...

[e-mike]

two of my friend here have one unit ...each one still going strong

[bruce750i]

V1 still good, box stock, 1.19 on 6s

I have 2 that are still up and running 1.17 firmware on 6S, ccbec and fan wired to run off ccbec

[gixxer]

still working in my e-revo on 6s.

[BrianG]

Still working on 4s ATM with my mod, will go to 5s in the future.

My first two v1's went up in smoke, but my 3rd v1 is going strong with the original firm ware. I just cut the top of the case off and run with no fan. Works great. Temps typically about 150 - 170 after a 10 or 15 minute main.

I run 5s with a Neu 1512 3d or 1515 2.5d depending on how I feel that day.

[jhautz]

I have a V1 that is still working v1.17 software and It just went back into the XT8 truggy to replace the V2 that had a BEC failure. I originally pulled out of the truggy to replace it with the V2 I got in replacement for my first failed V1. Not allot of run time on it yet. Maybe 3 hours or so. My 2 other V1s lasted well past this long before the BEC died in them, so I'm still holding my breath. The V2 I had only made it an hour or 2 before the BEC went. I still have a V2 that hasn't been plugged in yet. Waiting for the V1 to go first.

[RBMike]

Originally Posted by Edumakated

My first two v1's went up in smoke, but my 3rd v1 is going strong with the original firm ware. I just cut the top of the case off and run with no fan. Works great. Temps typically about 150 - 170 after a 10 or 15 minute main.

I run 5s with a Neu 1512 3d or 1515 2.5d depending on how I feel that day.

Edumakated, Internal bec?

[lincpimp]

Still have 1 v1 that works fine. Must have 1.17 firmware, as I do not remember changing it. I have played with the settings with the castle link quite a bit. Running 4s with a 1515 1.5d.

[jnev]

I have a V1 MMM (with no mods) that is going strong with lots of run time on it in my 8ight. I am using the stock firmware, or whatever it came withe when I bought it.

I also have a V2 MMM (with no mods as well) that is going strong too. I had a short test with it in my 8ight, and a short test with it in my CRT.5. I will have much more testing with it in the CRT.5 this upcoming weekend.

I also plan on buying one more MMM for my 8ight-T which will be running 6s. The 8ight and CRT.5 are both running 4s at the moment... but I can't be happier with the performance of the MMM's I currently have.

Edit: If anyone cares about the set ups, I am running a Hyperion 4s 5350mah pack in the 8ight with a Hitec HS-5997MG servo and Tekno Neu 1515/1y motor geared 47/17. And the CRT.5 has a Neu 1509/1.5y motor, Flightpower 4s 4370mah lipo pack and a Hitec HS-5245MG servo geared 46/16.

[auto2]

i do :-)

[VintageMA]

I have 2 v1 MMMs both with upgraded firmware working fine. Both running 6S with Neu 1515s and internal BEC.