other powerfull 1/8 esc

[BL_RV0]

[suicideneil]

Originally Posted by timaneli

does the 80a version be enough for a e-revo on 4s lipo?

regards

Borderline at best, though a few guys are using the 60 or 75amp versions in erevos with 4s lipo and 9XLs, so...

[timaneli]

Originally Posted by suicideneil

Borderline at best, though a few guys are using the 60 or 75amp versions in erevos with 4s lipo and 9XLs, so...

hello neil!!
no problem, i bought the 150a version too.....
and i received the 80a version today!!
look´s great and well built with a great fan,but only for next week will be tested!!!

regards

[BrianG]

Originally Posted by timaneli

...with a great fan...

Is there such a thing?

[timaneli]

Originally Posted by BrianG

Is there such a thing?

i don´t know!! but for a "chinese" esc look´s real good... i only don´t like to see the circuit board being outside the 2 sides of the case!!! hope it don´t break on a rough jumps or backflip...

[BrianG]

Well, the Mamba Max has an exposed circuit board, and it seems to hold up fine. I would just make sure that nothing metal could contact the exposed area, and you should be fine.

[timaneli]

Originally Posted by BrianG

Well, the Mamba Max has an exposed circuit board, and it seems to hold up fine. I would just make sure that nothing metal could contact the exposed area, and you should be fine.

so that is the problem of the mamba´s even on v3?

[BrianG]

You're probably thinking of the MMM, which is totally enclosed. The MM has the exposed PCB...

[timaneli]

Originally Posted by BrianG

You're probably thinking of the MMM, which is totally enclosed. The MM has the exposed PCB...

ok, my mistake!! the green mamba ok!!
let´s see how it handles this baby on my e-revo!!!
i will go to a motocross track and if it handles the jumps and falls it will handle the rest.................

[suicideneil]

The chinese esc looks like a sandwich with the ham poking out either side.. Should be okay, you'd need to really wrench down on the pcbs to snap them off, but it does kinda kill the otherwise clean and beasty look of the esc I must admit.

[timaneli]

Originally Posted by suicideneil

The chinese esc looks like a sandwich with the ham poking out either side.. Should be okay, you'd need to really wrench down on the pcbs to snap them off, but it does kinda kill the otherwise clean and beasty look of the esc I must admit.

what is the pcbs??

[lutach]

Originally Posted by timaneli

what is the pcbs??

The board that's hanging outside the plastic case.

[himalaya]

Originally Posted by lutach

HW asked for my help to find a motor manufacturer that would make a motor for them, but I'm going to save my good contacts for myself.

Right, a man could be very open, but not to anyone. You're understood pretty well.

BTW, they finally found some local guys to make motors for them, they were originally working with FG and now seem to have some new partnership. now they have 4 combos shipping:
80A ESC + 3665 BL 2300KV
80A ESC + 3674 BL 2350KV
150A ESC + 3674 BL 2350KV
150A ESC + 4465 BL 2000KV

[lutach]

Originally Posted by himalaya

Right, a man could be very open, but not to anyone. You're understood pretty well.

BTW, they finally found some local guys to make motors for them, they were originally working with FG and now seem to have some new partnership. now they have 4 combos shipping:
80A ESC + 3665 BL 2300KV
80A ESC + 3674 BL 2350KV
150A ESC + 3674 BL 2350KV
150A ESC + 4465 BL 2000KV

Yes, I'll be keeping my motor suppliers for myself now lol. I know who's making their motors and I hope they don't have any issues with them like I did. Here is the last e-mail I received from HW yesterday:

"Dear Luciano

Merry Chrismas to you . and we are public the new ESC 1:8 Ezrun150A is finished design and new Verson Xerun120A-v2 is finished too.

So late to contact you ."

Who knows, they might send me the 150A and the new Xerun.

[tntpower]

Does the programming card of the EZ-RUN 60a can be use to program this new EZ-RUN 150a?