RC-Monster Forums  

Go Back   RC-Monster Forums > Support Forums > Brushless
Reload this Page Neu upgrades their motors yet agian!

Reply
Page 1 of 2 1 2
 
Thread Tools Rate Thread Display Modes
Neu upgrades their motors yet agian!
Old
  (#1)
rootar
RC-Monster Titanium
 
rootar's Avatar
 
Offline
Posts: 1,803
Join Date: Aug 2005
Location: arkansas
Neu upgrades their motors yet agian! - 05.22.2009, 12:06 AM
i dunno if this is new but its new news to me. We just recived a motor back from service which has obviuos been completely replaced, and has quite a few notable changes.

-has a 16x5x4 front bearing, with the 13x5x4 rear bearing.
-has a removeable front endbell thats keyed in place with setscrew through both pieces
-has hex hardware holding the rear endbell on no more phillips!
-has grommets on wires, which are also double insulated
-has both m3 and m4 holes on a standard 25mm pattern.
-case is machined to where the fins start further back on the motor (to allow for machanical brakes better i assume.....?

but the stupid thing doesnt have a flat spot on the shaft so i gotta tear it down and fix that, but i looks pretty good. only other squak i have about it is that the way the front endbell is layed out you cant use mikes front cover/plate......
   
Reply With Quote
Old
  (#2)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
05.22.2009, 12:08 AM
Pictures man, pictures!
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Old
  (#3)
What's_nitro?
Soldermaster Extraordinaire
 
What's_nitro?'s Avatar
 
Offline
Posts: 4,529
Join Date: Apr 2007
Location: Plymouth, MA, USA
05.22.2009, 12:13 AM
Quote:
Originally Posted by BrianG View Post
Pictures man, pictures!
Uugghhhhhh! (Charlie Brown voice)
   
Reply With Quote
Old
  (#4)
rootar
RC-Monster Titanium
 
rootar's Avatar
 
Offline
Posts: 1,803
Join Date: Aug 2005
Location: arkansas
05.22.2009, 12:17 AM
yea the 16mm bearing in the front just looks STUPID big... maybe itll holdup better than these junk 13mm bearings theyve had in them... i should have another back very soon and im hoping it matched this type.

im uploading pics from my camera right now.
   
Reply With Quote
Old
  (#5)
js058515
Thank You Brushless Gods!
 
js058515's Avatar
 
Offline
Posts: 103
Join Date: Oct 2008
Location: SoCal
05.22.2009, 12:18 AM
Hurry up Ross!

Losi 8B 1.0, Tekno V3, Direct-Drive, 13/48, RX8, T8 1400kv
Losi 8B 1.5, Tekno V3 w/clutch (3-shoe), 14/48, MMM, Neu 1512 2Y
Losi 8T 2.0, Tekno V3 w/clutch (3-shoe), 14/48, MMM, T8 1550kv
   
Reply With Quote
Old
  (#6)
zeropointbug
Z-Pinch racer
 
zeropointbug's Avatar
 
Offline
Posts: 3,141
Join Date: Nov 2006
Location: SK, Canada
05.22.2009, 12:21 AM
This thread is useless without pictures!!!!!!!!!!!

“The modern astrophysical concept that ascribes the sun’s energy to thermonuclear reactions deep in the solar interior is contradicted by nearly every observable aspect of the sun.” —Ralph E. Juergens
   
Reply With Quote
Old
  (#7)
zeropointbug
Z-Pinch racer
 
zeropointbug's Avatar
 
Offline
Posts: 3,141
Join Date: Nov 2006
Location: SK, Canada
05.22.2009, 12:23 AM
Pictures!
Attached Thumbnails
Click image for larger version Name: pichers1.jpg Views: 420 Size: 77.9 KB ID: 7111  

“The modern astrophysical concept that ascribes the sun’s energy to thermonuclear reactions deep in the solar interior is contradicted by nearly every observable aspect of the sun.” —Ralph E. Juergens
   
Reply With Quote
Old
  (#8)
q8-maxx
E-Maxx Lover
 
q8-maxx's Avatar
 
Offline
Posts: 198
Join Date: Dec 2006
Location: kuwait
05.22.2009, 12:27 AM
wait stop flood lol

MMM v1 zippy 2x3s 5000mah neu 1y 1/8 diff's
MMM v3 Rc-monster 2x2s 5200mah-HC medusa 36-70-2300kv
Pic's - video - youtube video's
   
Reply With Quote
Old
  (#9)
rootar
RC-Monster Titanium
 
rootar's Avatar
 
Offline
Posts: 1,803
Join Date: Aug 2005
Location: arkansas
05.22.2009, 12:29 AM
here are the pics.

1st pic shows the new removable front bell, spacing, m3 and m4 holes, and the massive bearing.

2nd shows the fin spacing and the set screw keying the front endbell

3rd shows the hex hardware, grommets, insulation, 13mm bearing, and according to my caliper a thick rear case aroung the endbell...
Attached Thumbnails
Click image for larger version Name: new neu 001.jpg Views: 672 Size: 28.2 KB ID: 7112   Click image for larger version Name: new neu 002.jpg Views: 615 Size: 26.8 KB ID: 7113   Click image for larger version Name: new neu 003.jpg Views: 648 Size: 33.4 KB ID: 7114  

Last edited by rootar; 05.22.2009 at 12:31 AM.
   
Reply With Quote
Old
  (#10)
rootar
RC-Monster Titanium
 
rootar's Avatar
 
Offline
Posts: 1,803
Join Date: Aug 2005
Location: arkansas
05.22.2009, 12:33 AM
you guys are relentless couldnt even give me 25 mintues to find my camera and plug it in, snap some pics, up load them, resize them, and post them..... its gotten rough in here LOL

i always seem to get my hands on new stuff for some reason...
   
Reply With Quote
Old
  (#11)
rootar
RC-Monster Titanium
 
rootar's Avatar
 
Offline
Posts: 1,803
Join Date: Aug 2005
Location: arkansas
05.22.2009, 12:37 AM
btw if this thing had solder tabs instead of wire i think i would have messed my pants
   
Reply With Quote
Old
  (#12)
q8-maxx
E-Maxx Lover
 
q8-maxx's Avatar
 
Offline
Posts: 198
Join Date: Dec 2006
Location: kuwait
05.22.2009, 12:38 AM
looks very good but why they dont cover all the holes with grommets :(

thanks for the pictures

MMM v1 zippy 2x3s 5000mah neu 1y 1/8 diff's
MMM v3 Rc-monster 2x2s 5200mah-HC medusa 36-70-2300kv
Pic's - video - youtube video's
   
Reply With Quote
Old
  (#13)
lincpimp
Check out my huge box!
 
lincpimp's Avatar
 
Offline
Posts: 11,935
Join Date: Aug 2007
Location: Slidell, LA
05.22.2009, 12:39 AM
More hand porn...

I will have to get a closer look at the 1521 1y I just got. It definitely has the 3 piece can, but looked to have just a m4 thread 25mm pattern on it...

I will take some pics of it tomorrow and throw them up here.
   
Reply With Quote
Old
  (#14)
js058515
Thank You Brushless Gods!
 
js058515's Avatar
 
Offline
Posts: 103
Join Date: Oct 2008
Location: SoCal
05.22.2009, 12:43 AM
Thanks Rootar! I still like the Tekin or the Castle Nue but Tekin the most. Yayyyy Tekin.

Losi 8B 1.0, Tekno V3, Direct-Drive, 13/48, RX8, T8 1400kv
Losi 8B 1.5, Tekno V3 w/clutch (3-shoe), 14/48, MMM, Neu 1512 2Y
Losi 8T 2.0, Tekno V3 w/clutch (3-shoe), 14/48, MMM, T8 1550kv
   
Reply With Quote
Old
  (#15)
nitrostarter
RC-Monster Brushless
 
nitrostarter's Avatar
 
Offline
Posts: 3,156
Join Date: Jul 2005
Location: Gramercy, LA
05.22.2009, 01:00 AM
I like the 4mm bolt holes and bigger bearings, but dont like the 3 piece can design(cheaper)...

N. Rustler conversion
  Send a message via AIM to nitrostarter  
Reply With Quote
Reply
Page 1 of 2 1 2

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Forum Jump







Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top