RC-Monster Forums  

Go Back   RC-Monster Forums > Support Forums > Buggy

Reply
 
Thread Tools Rating: Thread Rating: 2 votes, 5.00 average. Display Modes
Old
  (#1)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
01.14.2010, 01:29 PM

Quote:
Originally Posted by superek4 View Post
Jammin conversion can only accept up to 16 pinion, I tried 17 the meshing was too tight.
Unfortunately, the only options you have to make it faster are:

- New motor with a higher kv. A CC/Neu 2650 motor runs great on 4s and the higher kv means you don't have to gear as tall and are within your gearing limits of the motor mount.

- Gear higher. I assume your gearing limitations are with the slot length on the motor mount. You might be able to modify the motor mount to lengthen the adjustment slots. A dremel with a carbide cutting bit is probably the best bet here. But, be careful about gearing up too high. 46/16 is already pretty tall. If you gear too high, you will be stressing the ESC as it tries to get an adequate back-EMF signal at low speeds. I personally wouldn't go much higher, if any, that what you are currently geared at.

- Go with higher voltage. 5s would be the best bet. If you are concerned about cost, Turnigy packs might be an option.

No matter what, it is going to cost more if you want more speed. You'll just have to decide which is the cheapest route to take.
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Old
  (#2)
jhautz
RC-Monster Mod
 
jhautz's Avatar
 
Offline
Posts: 4,217
Join Date: Apr 2006
Location: Chicago, IL
01.14.2010, 07:52 PM

Quote:
Originally Posted by BrianG View Post
Unfortunately, the only options you have to make it faster are:

- New motor with a higher kv. A CC/Neu 2650 motor runs great on 4s and the higher kv means you don't have to gear as tall and are within your gearing limits of the motor mount.

- Gear higher. I assume your gearing limitations are with the slot length on the motor mount. You might be able to modify the motor mount to lengthen the adjustment slots. A dremel with a carbide cutting bit is probably the best bet here. But, be careful about gearing up too high. 46/16 is already pretty tall. If you gear too high, you will be stressing the ESC as it tries to get an adequate back-EMF signal at low speeds. I personally wouldn't go much higher, if any, that what you are currently geared at.

- Go with higher voltage. 5s would be the best bet. If you are concerned about cost, Turnigy packs might be an option.

No matter what, it is going to cost more if you want more speed. You'll just have to decide which is the cheapest route to take.

or BIGGER TIRES! Try mounting some Savage XL tires on it. It'l go faster....


I can't decide if its more fun
to make it...
or break it...


Silent...But Deadly


   
Reply With Quote
Old
  (#3)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
01.14.2010, 10:47 PM

Quote:
Originally Posted by jhautz View Post
or BIGGER TIRES! Try mounting some Savage XL tires on it. It'l go faster....
True, I forgot to mention that. But just remember that going with larger tires is like gearing up and the same caution about gearing too high applies.
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump







Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com