Fs super cheap!!!, lots of truggy wheels/tires, loaded maxx roller, tx, charger, etc.

[Krawlin]

Need this stuff gone so I'm selling it cheap, WILL ALSO TRADE! PICTURES AVAILABLE UPON REQUEST! PLEASE PM ME OR EMAIL ME AT nitro_dude3@yahoo.com

The following is for sale -

Proline Truggy tires (glued), good for use as practice tires!

- 4 sets of 4 Holeshots on yellow LPR dish wheels, zero/standard offset, decent condition
PM ME FOR PRICE!
WILL SELL ALL 4 SETS TOGETHER, PM ME FOR PRICE!


- 1 set of 4 Holeshots on white LPR dish wheels, zero/standard offset (1 has a collapsed foam, otherwise in good condition)
PM ME FOR PRICE!


- 1 set of 4 Holeshot MT's on Kyosho spoked MT standard offset yellow wheels, 17mm hex, decent condition
PM ME FOR PRICE!


- 1 set of 4 Holeshot MT's on Kyosho spoked MT standard offset white wheels, 17mm hex (spokes have been sharpie'd red, not my doing) in decent condition
PM ME FOR PRICE!


- 1 set of 4 Crimefighter MT's on Kyosho spoked MT standard offset yellow wheels, 17mm hex, in decent condition
PM ME FOR PRICE!


- 1 set of 4 Crimefighter MT's on Mugen spoked MT standard offset white wheels, 17mm hex (spokes have been sharpie'd red, not my doing) in decent condition
PM ME FOR PRICE!

ALL TIRES ON THE MT WHEELS (LAST 4 LISTINGS) I WILL SELL TOGETHER! PM ME FOR PRICE!



1/8 scale diffs for sale -
- OFNA Hyper ST Pro Truggy diffs (standard diffs) (F/R) comes with pinions and bearings, BRAND NEW, NEVER USED, ONLY ASSEMBLED!
PM ME FOR PRICE!

- Hot Bodies Lightning Stadium Pro Diffs with helical cut ring gear (F/R), comes with bearings, no pinions.
PM ME FOR PRICE!



JR XR2i AM transmitter with receiver, both work, transmitter needs an antenna
PM ME FOR PRICE!



OFNA DigiPeak3 AC/DC charger, does 4S LiPo and 14cells NiMH, cannot balance, I will throw in a Electri-fly Equinox Balancer for free!
PM ME FOR PRICE!



LOADED E-MAXX/T-MAXX ROLLER!
This truck has a T-Maxx chassis but had brushless gear in it with a center diff motor mount. It can be turned into a nitro T-Maxx with all of the nitro gear or an E-Maxx with all of the brushless gear. It has some problems and has been used and it's dirty, but it's a highly upgraded truck and great for someone starting in the hobby who wants a blank slate of a truck as far as power goes but the rest is upgraded.
This truck has the following -
- UE Monoblock 7075-T6 chassis extension
- UE Knucklehead 7075-T6 shock towers
- Titanium front and rear skidplates (unknown brand)
- FLM 6061-T6 Aluminum Combo Bulks with 3906 diffs
- FLM aluminum diff cups for the 3906 diffs
- GH aluminum center braces
- GH aluminum steering
- GH aluminum center skidplate
- RPM arms all around
- RPM rear Tru-Track setup
- 3.3 Spec Revo Knuckles
- 3.3 Spec Revo front/rear driveshafts
- Traxxas Tubes Front Turnbuckles
- 4 OFNA shocks (1 has a broken shaft)
- 4 Traxxas Big Bores shocks
- T-Maxx 2.5 chassis

Does NOT come with -
- wheel hexes, wheels, tires
- electronics or nitro gear
- chassis is bare, no nitro stuff, no electric stuff, it's a blank slate.
- center shafts

What's wrong with it -
- Rear lower hinge pins are very difficult to get out, I can't figure out why, have replaced the pins, cleaned out the hinge pin hole, no luck.
- Front left OFNA shock has a broken shaft.
- Front left lower hinge pin is bent
- Front left driveshaft has a torn dust boot
- Front left driveshaft is missing the pin for the wheel hex.
- Chassis and lower braces have been clearanced for a center diff motor mount, I never had any strength issues with that though.
PM ME FOR PRICE! I WILL ACCEPT ANY REASONABLE OFFER!


I LET MY FEEDBACK SPEAK FOR ITSELF, 100% on RCTech (Krawlin), Ebay (rcbashsession), BYT (Krawlin), and RCU (Krawlin)!

PICTURES ARE AVAILABLE UPON REQUEST! PLEASE PM ME OR EMAIL ME AT nitro_dude3@yahoo.com FOR PICTURES OR OTHER INFO. PLEASE ASK ANY QUESTIONS YOU MIGHT HAVE! I WILL ALSO TRADE FOR ALOT OF THIS STUFF, JUST MAKE ME AN OFFER! ALL PRICES NEGOTIABLE! AGAIN, MAKE ME AN OFFER PLEASE!