RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Page 1 of 4 1 23 Last »
Showing results 1 to 25 of 91
Search took 0.07 seconds. Search: Posts Made By: Maxxman
Forum: Fastlane Machine 03.11.2012, 12:43 PM
Replies: 8
Views: 15,957
Posted By Maxxman
Ah, i see. I don't know about the XXL cvds i'm...

Ah, i see. I don't know about the XXL cvds i'm afraid. Yeah that should work for the stock axles, fingers crossed.

The savage cups, or any even longer, that i mentioned may add just enough length...
Forum: Fastlane Machine 03.11.2012, 12:08 PM
Replies: 8
Views: 15,957
Posted By Maxxman
Yeah, it looks like the ball and pin need to be...

Yeah, it looks like the ball and pin need to be further inside the diff cup, so the only way I can think of is to find a longer drive cup, such as a savage transmission drive cup (6x13x20) HPI 86276...
Forum: Fastlane Machine 03.11.2012, 10:07 AM
Replies: 8
Views: 15,957
Posted By Maxxman
Is there any material that you can remove from...

Is there any material that you can remove from the end of the stock drive shafts to line up the drive shaft and stub axle holes properly whilst maintaining its structural rigidity?

I have also...
Forum: Brushless 01.19.2012, 07:25 PM
Replies: 19
Views: 9,550
Posted By Maxxman
Could it not be that he simply has better...

Could it not be that he simply has better batteries so are less stressed and last longer?

His Thunder Power G6 65c batteries seem to capable of supplying 250A continuous and 500A burst (65x3.850...
Forum: General Questions 08.07.2008, 08:27 AM
Replies: 12
Views: 3,735
Posted By Maxxman
The Hyperion LBA10 is very popular and its the...

The Hyperion LBA10 is very popular and its the one i use. There are also lots of adapters available for it.
Forum: HPI Savage 08.07.2008, 08:21 AM
Replies: 194
Views: 40,704
Posted By Maxxman
No problem, glad that helped I've got one coming...

No problem, glad that helped I've got one coming for my flm savage, not quite as long as yours though:yes:. Good luck with the project.
Forum: HPI Savage 08.07.2008, 08:09 AM
Replies: 194
Views: 40,704
Posted By Maxxman
I rekon a genesis sized body would work since its...

I rekon a genesis sized body would work since its wheelbase is 60mm longer than the stock savage (397 verses 336.5) and is also 7mm longer, in wheelbase, than the XL which you said was a bit too...
Forum: Brushless 03.28.2008, 04:52 PM
Replies: 12
Views: 4,379
Posted By Maxxman
The e-mail that was returned from sending it to...

The e-mail that was returned from sending it to info@sky-technology.com said that the users mailbox was full but could send a brief message (<1kb) so I sent a "e-mail me if you get this, we need to...
Forum: Brushless 03.28.2008, 04:42 PM
Replies: 12
Views: 4,379
Posted By Maxxman
I've e-mailed S&T and Quark via three addresses...

I've e-mailed S&T and Quark via three addresses about my monster pro with the same problem and the e-mail sent to info@sky-technology.com came back as unable to be sent. I would also like to get the...
Forum: Brushless 03.28.2008, 08:04 AM
Replies: 127
Views: 50,415
Posted By Maxxman
Honestly, it isn't that hard. You just have to go...

Honestly, it isn't that hard. You just have to go slowly up and down with the disc at an angle to the shaft and make sure that you have a pinion available to check the shafts size. Just don't do too...
Forum: Brushless 03.28.2008, 07:12 AM
Replies: 127
Views: 50,415
Posted By Maxxman
To turn down the shaft run the motor whilst in a...

To turn down the shaft run the motor whilst in a vice and use a dremel or something similar with a cutting disc to cut down the shaft.
The KB should fit the revo mounts but the holes may have to be...
Forum: Brushless 03.28.2008, 06:48 AM
Replies: 13
Views: 3,676
Posted By Maxxman
My Monster Pro burnt but not as bad as...

My Monster Pro burnt but not as bad as yours:yes:.
I've decided i'll send it back as there's not much else i can do. It's just a question of contacting them.
In the past i think i got maybe one...
Forum: Brushless 03.27.2008, 06:37 PM
Replies: 13
Views: 3,676
Posted By Maxxman
I have just tested it with a simple 2 channel...

I have just tested it with a simple 2 channel radio with a servo as well. Servo worked fine but nothing new with the esc.

I think I'm going to send it back - shall I just send it in or try again...
Forum: Brushless 03.27.2008, 06:14 PM
Replies: 13
Views: 3,676
Posted By Maxxman
Yeah I have the motor plugged in. Even if it...

Yeah I have the motor plugged in. Even if it wasn't, that wouldn't make it act the way that it currently is.
Forum: Brushless 03.27.2008, 06:08 PM
Replies: 13
Views: 3,676
Posted By Maxxman
This monster Pro is actually a replacement one...

This monster Pro is actually a replacement one sent from S&T for one that smoked. that one however was used on a different radio (TQ3), so i kind of know how to program it.
You are right, I can't...
Forum: Brushless 03.27.2008, 05:37 PM
Replies: 13
Views: 3,676
Posted By Maxxman
I set the throttle EPA's to max( +140% -160%) and...

I set the throttle EPA's to max( +140% -160%) and made sure that the throttle was centred. That didn't work and previously I had popped the cover off and tried to press the button that way and that...
Forum: Brushless 03.27.2008, 05:22 PM
Replies: 13
Views: 3,676
Posted By Maxxman
Thanks, I'll give that a try and see if the works.

Thanks, I'll give that a try and see if the works.
Forum: Brushless 03.27.2008, 05:15 PM
Replies: 13
Views: 3,676
Posted By Maxxman
Programming a Monster Pro and S&T e-mail address

My 125b doesn’t program, no matter how many times I try.:grrrrrr: I hold the program button and turn it on and there are no beeps when throttle is moved and the first red led lights up as soon as it...
Forum: General Electric 03.27.2008, 07:01 AM
Replies: 7
Views: 3,012
Posted By Maxxman
Neither, the hyperion eos 1210i that Mahazael is...

Neither, the hyperion eos 1210i that Mahazael is asking about.
Forum: General Electric 03.26.2008, 06:14 PM
Replies: 7
Views: 3,012
Posted By Maxxman
I have one. It works fine for what i want and has...

I have one. It works fine for what i want and has lots of info available to the user during and after charging.
Forum: Brushless 03.26.2008, 06:08 PM
Replies: 10
Views: 3,748
Posted By Maxxman
The 8xl will give you longer run times and tax...

The 8xl will give you longer run times and tax the MM less but be slower. Although you could gear up a little to compensate fo the lower KV if you wanted.
Forum: Brushless 03.26.2008, 06:00 PM
Replies: 10
Views: 3,748
Posted By Maxxman
I run the MM in a FLM converted savage. The MM...

I run the MM in a FLM converted savage. The MM will be fine but the 4600 motor won't be up to much.
Forum: General Discussion 03.25.2008, 12:27 PM
Replies: 21
Views: 3,762
Posted By Maxxman
I use the Hyperion eos1210i and a lba10 balancer.

I use the Hyperion eos1210i and a lba10 balancer.
Forum: Brushless 03.22.2008, 03:40 PM
Replies: 27
Views: 6,841
Posted By Maxxman
You could flip the diffs, but you may need to...

You could flip the diffs, but you may need to take the whole vehicle apart to do so.
Forum: General Electric 02.14.2008, 03:41 PM
Replies: 8
Views: 3,103
Posted By Maxxman
I believe the 1p's voltage would drop more than...

I believe the 1p's voltage would drop more than that of the 2p's under the same load and therefore heat up more.
Showing results 1 to 25 of 91
Page 1 of 4 1 23 Last »

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top