RC-Monster Forums  

Go Back   RC-Monster Forums > Search Forums
Reload this Page Search Results

Showing results 1 to 18 of 18
Search took 0.01 seconds. Search: Posts Made By: Nautilus
Forum: Brushless 10.20.2009, 05:10 PM
Replies: 6
Views: 6,774
Posted By Nautilus
true, but accessability in most of these tanks is...

true, but accessability in most of these tanks is a PITA.

I'm sold on brushless/lipo and not just for sheer horsepower.
Forum: Brushless 10.20.2009, 04:00 PM
Replies: 6
Views: 6,774
Posted By Nautilus
Eh. Nevermind. It appears that the Tamiya esc...

Eh. Nevermind. It appears that the Tamiya esc (which also coordinates with a sound unit and can't practically be switched out) only works with brushed motors.
Forum: Brushless 10.20.2009, 11:08 AM
Replies: 6
Views: 6,774
Posted By Nautilus
Brushless 380s for a Tamiya tank...

So I am getting a Tamiya tank 25 years after I initially wanted one. The tank uses two brushed 380 motors for locomotion and turning the turret.

I was wondering if there are suitable high...
Forum: T/E Maxx Parts 08.11.2009, 11:24 AM
Replies: 9
Views: 5,501
Posted By Nautilus
OT question: does adding a center diff reduce the...

OT question: does adding a center diff reduce the offroad ability of a truck, at least theoretically? (similar to how f/r diffs hurt offroad ability)
Forum: T/E Maxx Parts 08.10.2009, 11:30 AM
Replies: 1
Views: 3,573
Posted By Nautilus
3905 FLM chassis w/hybrid bulks...

If I use the FLM 3905 chassis in combination with the FLM hybrid bulks + HB diffs, will the center dogbones that come with the chassis fit?
Forum: T/E Maxx Parts 08.10.2009, 11:06 AM
Replies: 9
Views: 5,501
Posted By Nautilus
Is he making a slipperential mount for the 3905...

Is he making a slipperential mount for the 3905 chassis? Or is there already a mount for the 3905 available?
Forum: Revo 08.10.2009, 10:56 AM
Replies: 5
Views: 3,588
Posted By Nautilus
RCM hybrid diffs

So after 1 year of the RCM V3 hybrid diffs sitting around, I finally decided to complete my brushless conversion for my nitro Revo. I am using a Kershaw E-Revo chassis with a new E-Revo tranny. The...
Forum: Revo 02.03.2009, 01:09 PM
Replies: 4
Views: 2,622
Posted By Nautilus
Oh, I didn't realize I needed to slightly mod the...

Oh, I didn't realize I needed to slightly mod the input shaft.

Thanks.
Forum: Revo 02.03.2009, 12:05 PM
Replies: 4
Views: 2,622
Posted By Nautilus
You seat the yoke all the way against the...

You seat the yoke all the way against the bearing?

If I put the set screw of the yolk on the flat part of the input shaft, the space between the base of the yolk and the bearing is more than...
Forum: Revo 02.03.2009, 01:33 AM
Replies: 4
Views: 2,622
Posted By Nautilus
REvo hybrid diff question...

I am in the process of installing these. Question though--how do you keep the input shaft ball bearing (the one on the outside of the diff case) from popping out?
Forum: Revo 12.11.2008, 02:07 AM
Replies: 1
Views: 2,564
Posted By Nautilus
Spur and pinion suggestions...

E-Revo transmission with V2 RCM hybrid diffs (with buggy diff) and 2200 kv CC motor on 6s. Can anyone suggest a good starting point for a pinion and spur?

This is for bashing so a balance between...
Forum: Revo 12.05.2008, 02:17 PM
Replies: 2
Views: 3,389
Posted By Nautilus
2 questions about the V2 RCM diffs...

1. Can I use the stock revo axles (6mm?) with the outdrives on the diff (also 6mm? or 8mm?)?

2. If I use a dogbone center drive shaft, can I use a 6mm drive cup on the tranny and an 8mm drive...
Forum: HPI Savage 12.04.2008, 11:39 AM
Replies: 134
Views: 59,962
Posted By Nautilus
anyone concerned about the lack of airflow over...

anyone concerned about the lack of airflow over the motor?
Forum: HPI Savage 12.03.2008, 01:46 AM
Replies: 134
Views: 59,962
Posted By Nautilus
This thing looks *way* better built than the...

This thing looks *way* better built than the E-Revo or an E-maxx. I have a 3905 E-maxx and frankly I was disappointed at how flimsy it feels, especially the chassis. The plastic used in the...
Forum: General Questions 05.05.2008, 01:33 PM
Replies: 2
Views: 2,121
Posted By Nautilus
Yeah, I actually do have what sounds and feels...

Yeah, I actually do have what sounds and feels like glitching, where the steering servos make that glitching noise (constant jerky movement) and refuse to move for a few seconds.

I'll try...
Forum: General Questions 05.04.2008, 11:24 PM
Replies: 2
Views: 2,121
Posted By Nautilus
Compro 160/18 and new Emaxx...

I'm looking for settings for the Compro 160/18 for the new E-maxx. I have a low kV Neu motor hooked up as well and stock radio. I know the Neu is 4 pole and have already set the controller for...
Forum: Brushless 02.09.2008, 11:30 PM
Replies: 5
Views: 1,950
Posted By Nautilus
This has got to be it. I guess I will try...

This has got to be it. I guess I will try dremeling the plate and if that doesn't work I will have to get a custom mount.
Forum: Brushless 02.09.2008, 10:01 PM
Replies: 5
Views: 1,950
Posted By Nautilus
Question about mounting Neu

So I go to mount my Neu 1515 motor to my new Emaxx and it turns out the mounting holes on the motor are not spaced far enough apart to get the 2 screws in at the same time. The motor holes on the...
Showing results 1 to 18 of 18

 
Forum Jump






Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com

Contact Us - RC-Monster Store - Archive - Top