Testing a couple of 1/10 120A ESC (Pictures of the 200A is in here too)

[lutach]

Originally Posted by ffactory666

That's great to know , what kv is the Aveox RC7 . Trying to work out what rpm you were spinning on 3S as if it's similar to the Orion on 2s i will gear very similar with 19/72, pitty i only have pinions from 22t - 26t i will have to buy a couple more.. 80mph is plenty for me to get started as i haven't gone over 60mph before

I'll get use to that and how the car needs to be set up and feels and will then try and go faster .

The RC7 motor has a little over 4000Kv. Your 22-26T pinion will be nice .

Originally Posted by lutach

The RC7 motor has a little over 4000Kv. Your 22-26T pinion will be nice .

Sweet , now to order a car

[BL_RV0]

What are you going to get? I'd go for a buggy if you don't have one already.

Originally Posted by BL_RV0

What are you going to get? I'd go for a buggy if you don't have one already.

If you look at my sig you can see what buggy and truggy i already have

I am getting a BMI DB10R pan car for a 2s speed run car .

How did you go drag racing on the weekend Luciano?

[lutach]

Originally Posted by ffactory666

How did you go drag racing on the weekend Luciano?

It was too cold and windy. I couldn't get m drag car and the bike to hook up right. I almost destroyed the bike. It launched straight and then for some reason it went to the left and I couldn't bring it back to the right, so it went off flying. Only damage though was a broken CF wheelie bar. I'm going to wait until summer time now. Plus I might make my own drag bike as I don't like the design of the one I'm running.

[lutach]

Lincpimp,

The sensored ESC got shipped out today so you can test it in the crawler. Please post feedbacks here.

Regards.

Originally Posted by lutach

It was too cold and windy. I couldn't get m drag car and the bike to hook up right. I almost destroyed the bike. It launched straight and then for some reason it went to the left and I couldn't bring it back to the right, so it went off flying. Only damage though was a broken CF wheelie bar. I'm going to wait until summer time now. Plus I might make my own drag bike as I don't like the design of the one I'm running.

Sorry about the bike man , it would of been spectacular to capture on video . i didn't even know there was rc drag bikes .
Was looking forward to reports on the 200A esc .

[lincpimp]

Originally Posted by lutach

Lincpimp,

The sensored ESC got shipped out today so you can test it in the crawler. Please post feedbacks here.

Regards.

Sounds good. A little background for everyone else.

I am currently running a novak xrs with a 13.5 motor in my cr-01 tamiya crawler. It is a bit of a fast setup, but it is geared as low as possible, and has very good low speed driveability, plus about 10mph top speed. So it is fun to play with, and plenty capable when crawling.

I would like to run a 21.5 motor on 3s, but want to keep the sensored design. Novak does not make any escs that can handle 3s lipo. I may also try a 17.5 motor as it would have the same rpm on 3s as my 13.5 does on 2s.

I will test the esc to see how it does in the crawler enviorment...

[lutach]

Originally Posted by ffactory666

Sorry about the bike man , it would of been spectacular to capture on video . i didn't even know there was rc drag bikes .
Was looking forward to reports on the 200A esc .

The bike is ok and I did get it on video. The 200A has proven itself it the previous race. When the weather warms up, I'll be trying to put it in the record books.

[lutach]

Originally Posted by lincpimp

Sounds good. A little background for everyone else.

I am currently running a novak xrs with a 13.5 motor in my cr-01 tamiya crawler. It is a bit of a fast setup, but it is geared as low as possible, and has very good low speed driveability, plus about 10mph top speed. So it is fun to play with, and plenty capable when crawling.

I would like to run a 21.5 motor on 3s, but want to keep the sensored design. Novak does not make any escs that can handle 3s lipo. I may also try a 17.5 motor as it would have the same rpm on 3s as my 13.5 does on 2s.

I will test the esc to see how it does in the crawler enviorment...

Sounds good lincpimp. My sensored ESC will handle 3S lipos and you don't need an external BEC. I used 3S lipos in my drag bike and I used the ESC's BEC and it worked fine.

[lutach]

The drag bike had my own 100A sensored ESC, 5.5T sensored motor and 3S 2200mAh 25C pack. Here are a few pictures of the bike that I raced (Video will be added after it's done processing ):

[lutach]

Here is the video:

http://www.youtube.com/watch?v=8VL2U_JgNWc

[SunnyHouTX]

You have PM.

[snellemin]

Nice solid launch man.