RC-Monster Forums  

Go Back   RC-Monster Forums > Support Forums > Team Tekin

Reply
 
Thread Tools Rate Thread Display Modes
I'm geting a R1 pro thats been fried for $20
Old
  (#1)
whitrzac
Can't catch this...
 
whitrzac's Avatar
 
Offline
Posts: 1,142
Join Date: Oct 2008
Location: baraboo, WI
I'm geting a R1 pro thats been fried for $20 - 12.01.2008, 05:00 PM

I guy used it in a 1/8 conversion and let the smoke out somehow, I'v been told that 1 of the FETs is fried,


these are the exact quotes.
Quote:
Tekin R1 Pro - This might be burnt up. Smoke came out of it after making weird beeps so I'm assuming it's done. It will be sold as-is. I can take it apart and check it out. I can also take pics too. This is a lot of money down the drain and is the reason for me selling. Comes with deans plugs, the stock capacitor, factory packaging and decals, two 35V 1200uf caps from Mike, and 4mm connectors installed. I'm gonna ask $40 shipped since it may still be good but give me an offer if you think that's too much.

took it apart, one of the FETs is toast. If you had the time and finesse to take it apart and replace the FET and anything else burnt up, you could have a new ESC practically.

any idea on how much $$ it will cost to fix?
   
Reply With Quote
Old
  (#2)
BrianG
RC-Monster Admin
 
BrianG's Avatar
 
Offline
Posts: 14,609
Join Date: Nov 2005
Location: Des Moines, IA
12.01.2008, 06:24 PM

Well, if you can figure out which FET to buy, sucessfully solder a surface mount device without bridging any terminals, and that is the ONLY thing that is wrong, you could have it done pretty cheaply. First thing is to figure out the part number and go from there...

Personally, I'd see about getting it fixed from Tekin. Might possibly be more than fixing it yourslef, but may be cheaper in the long run if more than one component is bad...
  Send a message via Yahoo to BrianG Send a message via MSN to BrianG  
Reply With Quote
Old
  (#3)
lutach
RC-Monster Dual Brushless
 
lutach's Avatar
 
Offline
Posts: 5,139
Join Date: Sep 2006
12.01.2008, 06:51 PM

I know GriffinRU can fix it, but I haven't heard from him in a while now. He might even have the MOSFET with him. I know I sent him a few to fix my 60A ESC and it uses the same FET. Let me know if you want to sell it, cause I want to make me a 4 MOSFET (416A lol) board Super R1 Pro lol.
  Send a message via MSN to lutach  
Reply With Quote
Old
  (#4)
whitrzac
Can't catch this...
 
whitrzac's Avatar
 
Offline
Posts: 1,142
Join Date: Oct 2008
Location: baraboo, WI
12.01.2008, 11:39 PM

I can probly do it, I used to be able stack 6 prong FETs 4 high without them going poof(xmod/moneypit)
I was planing on sending it in to tekin, but doo you think that tekin could repair it? I looked at there website and they say that they can do it for $40 IF its repairable, anyone know how much it would be if it wasnt?
   
Reply With Quote
Old
  (#5)
BL_RV0
RC-Monster Dual Brushless
 
BL_RV0's Avatar
 
Offline
Posts: 5,061
Join Date: Oct 2007
Location: Thousand Oaks CA
12.02.2008, 12:41 AM

That's lame, castle says $50 no matter what shape it is in.


Get me back into RC!
  Send a message via Yahoo to BL_RV0 Send a message via AIM to BL_RV0 Send a message via MSN to BL_RV0  
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump







Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
vBulletin Skin developed by: vBStyles.com